Read Sony DHC-EX880MD / DHC-MD717 / MDS-EX880 / MDS-MS717 Service Manual online
– 12 –
7.
OPERATING THE CONTINUOUS PLAYBACK
MODE
MODE
7-1. Entering the Continuous Playback Mode
1. Set the disc in the slot 1 of unit. (In several seconds it will be
automatically pulled in.) (Whichever recordable discs or discs
for playback only are available.)
for playback only are available.)
2. Turn the
[
=
SELECTOR
+
]
dial and display “CPLAY
MODE”.
3. Press the
[ENTER/YES]
button to change the display to
“CPLAY MID”.
4. When access completes, the display changes to
“C =
AD =
)”.
Note:
The numbers “ ” displayed show you error rates and ADER.
7-2. Changing the Parts to be Played-back
1. Press the
[ENTER/YES]
button during continuous playback
to change the display as below.
2. When access completes, the display changes to
“C =
AD =
)”.
Note:
The numbers “ ” displayed show you error rates and ADER.
7-3. Ending the Continuous Playback Mode
1. Press the
[MENU/NO]
button. The display will change to
“CPLAY MODE”.
2. Press the
§ button and remove the disc. (To exit from the
TEST mode, press the
[REPEAT]
button.)
Notes:
1.
The playback start address for IN, MID, and OUT are as follows.
IN
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
In case you want to display the address of the playback position on
the display, press the
OUT : 700h cluster
In case you want to display the address of the playback position on
the display, press the
[DISPLAY]
button and display “CPLAY
(
)”.
2.
The
[MENU/NO]
button can be used to stop playing anytime.
8.
OPERATING THE CONTINUOUS RECORDING
MODE
MODE
8-1. Entering the Continuous Recording Mode
1. Set the MO disc in the slot 1 of unit. (Refer to note 3.)
2. Turn the
2. Turn the
[
=
SELECTOR
+
]
dial and display “CREC
MODE”.
3. Press the
[ENTER/YES]
button to change the display to “CREC
MID”.
4. When access completes, the display changes to “CREC
(
)” and
[PROGRAM]
LED lights up.
Note:
The numbers “ ” displayed shows you the recording position ad-
dress.
dress.
8-2. Changing the Parts to be Recorded
1. When the
[ENTER/YES]
button is pressed during continuous
recording, the display changes as below. (“PROGRAM”
indication turns off during change-over of display.)
indication turns off during change-over of display.)
2. When access completes, the display changes to “CREC
(
)” and
[PROGRAM]
LED lights up.
Note:
The numbers “ ” displayed shows you the recording position ad-
dress.
dress.
8-3. Ending the Continuous Recording Mode
1. Press the
[MENU/NO]
button. The display will change to
“CREC MODE” and
[PROGRAM]
LED goes off.
2. Press the
§ button and remove the disc.
Notes:
1.
The recording start address for IN, MID, and OUT are as follows.
IN
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
OUT : 700h cluster
2.
The
[MENU/NO]
button can be used to stop recording anytime.
3.
During the test mode, the erasing-protection tab will not be detected.
Therefore be careful not to set the continuous recording mode when a
disc not to be erased is set in the unit.
Therefore be careful not to set the continuous recording mode when a
disc not to be erased is set in the unit.
4.
Do not perform continuous recording for long periods of time above
5 minutes.
5 minutes.
5.
During continuous recording, be careful not to apply vibration.
9.
EEP MODE
This mode reads and writes the contents of the non-volatile
memory.
It is not used in servicing. If set accidentally, press the
memory.
It is not used in servicing. If set accidentally, press the
[MENU/NO]
button immediately to exit it.
CPLAY MID
CPLAY OUT
CPLAY IN
CREC MID
CREC OUT
CREC IN
Click on the first or last page to see other DHC-EX880MD / DHC-MD717 / MDS-EX880 / MDS-MS717 service manuals if exist.