Read Sony DAV-FR1 / HCD-F100 / HCD-F50 / HCD-FR1 / MHC-F100 / MHC-F50 / MHC-FR1 Service Manual online
– 6 –
Ve
r. 1.1
r. 1.1
6
1
Press
t/CLOCK SET.
The hour indication flashes.
2
Turn the jog dial to set the hour.
The clock is on a 12-hour system.
3
Press ENTER.
The minute indication flashes.
Step 2: Setting the
time
time
You must set the time before using the timer
functions.
functions.
4
Turn the jog dial to set the minute.
5
Press ENTER.
The clock starts working.
Tips
• If you’ve made a mistake, start over from step 1.
• Setting the time deactivates the demo mode .
• Setting the time deactivates the demo mode .
If you want to display the demo mode, press
DISPLAY/DEMO when the power is off.
DISPLAY/DEMO when the power is off.
2,4 3,5
1
1 2 : 0 0 A M
RELAY
TUNED
1 2 REC SLEEP
DOLBY NR B OFF
STEREO
MONO
SYNC
MONO
SYNC
STEP
REC
kHz
MHz
VOLUME
PLUS 1
7 : 0 0 P M
7
n
Step 3: Presetting
radio stations
radio stations
For Singaporian model, you can preset up to
40 stations, 20 for FM, 10 for MW and 10 for
SW. For North and South American and
Australian models, you can preset up to 30
stations, 20 for FM and 10 for AM.
40 stations, 20 for FM, 10 for MW and 10 for
SW. For North and South American and
Australian models, you can preset up to 30
stations, 20 for FM and 10 for AM.
4
Press TUNER MEMORY.
A preset number appears in the display.
5
Turn the jog dial to select the
desired preset number.
desired preset number.
6
Press ENTER.
The station is stored.
7
Repeat steps 1 to 6 to store other
stations.
stations.
To tune in a station with a weak
signal
signal
Press TUNING MODE repeatedly until
“MANUAL” appears in step 2, then turn the
jog dial to tune in the station.
“MANUAL” appears in step 2, then turn the
jog dial to tune in the station.
To change the preset number
Start over from step 1.
To change the AM tuning interval
The AM tuning interval is factory-preset to 10
kHz (9 kHz in some areas). To change the
AM tuning interval, tune in any AM station
first, then turn off the power. While holding
down the ENTER button, turn the power
back on. When you change the interval, AM
preset stations will be erased. To reset the
interval, repeat the same procedure.
kHz (9 kHz in some areas). To change the
AM tuning interval, tune in any AM station
first, then turn off the power. While holding
down the ENTER button, turn the power
back on. When you change the interval, AM
preset stations will be erased. To reset the
interval, repeat the same procedure.
Tip
The preset stations are retained for half a day even if
you unplug the power cord or if a power failure
occurs.
you unplug the power cord or if a power failure
occurs.
1
Press TUNER/BAND repeatedly
until the band you want appears in
the display.
until the band you want appears in
the display.
Every time you press this button, the
band changes as follows:
Singaporian models:
FM n MW n SW
band changes as follows:
Singaporian models:
FM n MW n SW
North and South American and
Australian models:
FM ˜ AM
Australian models:
FM ˜ AM
2
Press TUNING MODE repeatedly
until “AUTO” appears.
until “AUTO” appears.
3
Turn the jog dial.
The frequency indication changes and
scanning stops when the system tunes in
a station. “TUNED” and “STEREO” (for
a FM stereo program) appear.
scanning stops when the system tunes in
a station. “TUNED” and “STEREO” (for
a FM stereo program) appear.
POWER
3,5 6
2
1
4
Preset number
AUTO
TUNED
STEREO
STEREO
VOLUME
M E M O R Y F M 1 ?
20
AUTO
TUNED
STEREO
STEREO
MHz
VOLUME
F M 1 0 0 . 5 0
20
Click on the first or last page to see other DAV-FR1 / HCD-F100 / HCD-F50 / HCD-FR1 / MHC-F100 / MHC-F50 / MHC-FR1 service manuals if exist.