CMT-M100MD, HCD-M10 - Sony Audio Service Manual (repair manual). Page 36

36

Mode which sets the adjustment results recorded in the non-volatile
memory to the initial setting value. However the results of the tempera-
ture compensation offset adjustment will not change to the initial setting
value.
If initial setting is performed, perform all adjustments again excluding the
temperature compensation offset adjustment.
For details of the initial setting, refer to “4. Precautions for Adjustments”
(See page 32) and execute the initial setting before the adjustment as re-
quired.

Procedure:
1. Press the

. 

“R” or

>

 

“R” button to display “ADJ

CLEAR”  (C28).

2. Press the ENTER/YES “R” button.  “Complete!” will be

displayed momentarily and initial setting will be executed, after
which “ADJ CLEAR” (C28) will be displayed.

The Iop data can be recorded in the non-volatile memory. The Iop
value on the optical pick-up label and the Iop value after the
adjustment will be recorded. Recording these data eliminates the
need to read the label on the optical pick-up.

Recording Procedure:
1. Press the

. 

“R” or

 >

 

“R” button to display “Iop Write”

(C05), and press the ENTER/YES “R” button.

2. The display becomes “Ref=@@@.@” (@ is an arbitrary

number) and the numbers which can be changed will blink.

3. Input the Iop value on the optical pick-up label.

To select the number : Press the

. 

“R” or

 >

 

“R” button.

To select the digit : Press the  REC MODE  button.

4. When the ENTER/YES “R” button is pressed, the display

becomes “Measu=@@@.@” (@ is an arbitrary number).

5. As the adjustment results are recorded for the step 4 value. Leave

it as it is and press the ENTER/YES “R” button.

6. “Complete!!” will be displayed momentarily. The value will be

recorded in the non-volatile memory and the display will become
“Iop Write” (C05).

Display Procedure:
1. Press the

. 

“R” or 

 >

 

“R” button to display “Iop Read”(C26).

2. Press the ENTER/YES “R” button.
3. “@@.@/##.#” is displayed and the recorded contents are

displayed.
@@.@ indicates the Iop value on the optical pick-up label.
##.# indicates the Iop value after adjustment

4. To end, press the MENU/NO “R” button to display “Iop Read”

(C26).

Save the temperature data at that time in the non-volatile memory
as 25 ˚C reference data.

1. Usually, do not perform this adjustment.
2. Perform this adjustment in an ambient temperature of 22 ˚C to 28 ˚C.

Perform it immediately after the power is turned on when the internal
temperature of the unit is the same as the ambient temperature of 22 ˚C
to 28 ˚C.

3. When D101 has been replaced, perform this adjustment after the tem-

perature of this part has become the ambient temperature.

Procedure:
1. Press the

. 

“R” or

  >

 

“R” button to display “TEMP

ADJUST” (C03).

2. Press the ENTER/YES “R” button to select the “TEMP

ADJUST” mode.

3. “TEMP = 

 [OK]” and the current temperature data will be

displayed.

4. To save the data, press the ENTER/YES “R” button.

When not saving the data, press the MENU/NO “R” button.

5. When the ENTER/YES “R” button is pressed, “TEMP = 

SAVE” will be displayed and turned back to “TEMP ADJUST”
(C03) display then.

Specified Value:
The “TEMP =  

” should be within “E0 - EF”, “F0 - FF”, “00 -

0F”,  “10 - 1F” and “20 - 2F”.

Before starting adjustment;
Check the Iop value of the optical pick-up before adjustments.
(Refer to 8. Recording and Displaying the Iop Information)

Procedure:
1. Insert the laser power meter probe into the disk insertion slot

and set it on top of the objective lens of the optical pick-up.
(When it cannot be set properly, press the

m

 

 button or

M

button to move the optical pick-up)

Connect the digital voltmeter to CN105 pin 1 (I+3V) and
CN105pin 2 (Iop) on the BD board.

2. Press the

. 

“R” or

  >

 

“R” button to display “LDPWR

ADJUST” (C04).
(Laser power : For adjustment)

3. Press the ENTER/YES “R” button once to display “L 0.9 mW

$ 

”.

4. Press the

. 

“R” or 

 >

 

“R” button until the laser power

meter reading matches with the specified value.
Press the ENTER/YES “R” button after setting the range knob
of the laser power meter to 10mW, and save the adjustment
results. (“LD SAVE $ 

” will be displayed for a moment)

5. Then “L 7.0 mW $ 

” will be displayed.

Optical pick-up
objective lens

laser
power meter

+
–

BD board

digital voltmeter

CN105 pin 

1

 (I+3V)

CN105 pin 

2

 (Iop)