Read Sony CDP-X3000 / CDP-X3000ES Service Manual online
– 3 –
SECTION 1
SERVICING NOTES
1-1. WRITING FOCUS/TRACKING AUTO GAIN
DATA
In general for the CD players that use a digital servo IC, the focus/
tracking gain is automatically adjusted each time a disc is changed.
In this set, the gain in test disc (YEDS-18) has been written to a
nonvolatile memory (IC803: X24C01S) on the Display Board, and
therefore the gain is not readjusted even if a disc is changed.
Accordingly, always write auto gain data when replacing the Servo
Board, IC803 on Display Board, or optical pick-up.
tracking gain is automatically adjusted each time a disc is changed.
In this set, the gain in test disc (YEDS-18) has been written to a
nonvolatile memory (IC803: X24C01S) on the Display Board, and
therefore the gain is not readjusted even if a disc is changed.
Accordingly, always write auto gain data when replacing the Servo
Board, IC803 on Display Board, or optical pick-up.
1) Connect CN805 1 pin (IN/OUT SW) and 6 pin (GND) on
Display Board.
Under this condition, the set will operate even when the disc lid
is open (or Key Board is not connected).
Under this condition, the set will operate even when the disc lid
is open (or Key Board is not connected).
2) Connect TP (ADJ: CN105 3 pin) on Servo Board to GND, and
TP (VC: CN108 2 Pin) to TP3 (TEI: IC105 @¶ pin) with lead
wires respectively.
wires respectively.
3) Connect an oscilloscope to TP (TE: CN108 1 pin).
4) Insert the test disc (YEDS-18), turn on POWER switch, and
play fifth music with
· (PLAY) and AMS Keys on the
Remocon.
5) Adjust RV101 so that the waveform on oscilloscope is verticolly
symmetric with respect to the A [Vdc], and also its level is 1.3 ±
0.6 Vp-p.
0.6 Vp-p.
At this time, A/B
×
100 = ± 22 (%) or less
6) The auto gain data are written when a lead wire between TP
(ADJ: CN105 3 pin) and GND is removed.
Note: If the POWER switch was turned on without connecting TP
(ADJ) to the GND, auto gain data are not written to the
memory even if a disc is inserted, but the previous data saved
in the memory are used as focus/tracking data.
memory even if a disc is inserted, but the previous data saved
in the memory are used as focus/tracking data.
1-2. AF MODE
With the TP (AFJ: CN105 2 Pin) connected to the GND on Servo
Board, turn on the POWER switch, and the AF mode is activated
and the following checking can be made.
Board, turn on the POWER switch, and the AF mode is activated
and the following checking can be made.
1-2-1. FL tube check
All tubes turn on, then if
· button is pressed, the display will be
as shown below. (Segment ON 1)
(Segment ON 1)
6
16
2
12
8
18
4
14
10
20
(Segment ON 2)
0Vdc
B
A
symmetric
level: 1.3 ± 0.6 Vp-p
IF
P button is pressed, the display will be as shown below. (Seg-
ment ON 2)
+
–
–
SERVO board
TP (TE)
TP (VC)
TP (VC)
Oscilloscope
If STOP
p is pressed, all tubes turn on again.
Click on the first or last page to see other CDP-X3000 / CDP-X3000ES service manuals if exist.