Read Sony CDP-CE500 Service Manual online
CDP-CE500
CDP-CE500
19
19
SECTION 4
ELECTRICAL CHECK
Note:
1. CD Block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
1. CD Block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat-
ed.
3. Use an oscilloscope with more than 10 M
Ω impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specifi ed value with the following checks.
5. Check the focus bias check when optical pick-up block is replaced.
FOCUS BIAS CHECK
+
–
–
BD75 board
oscilloscope
(DC range)
CL102 (RFOUT)
CL117 (VREF)
Procedure:
1. Connect the oscilloscope to CL102 (RFOUT) and CL117
1. Connect the oscilloscope to CL102 (RFOUT) and CL117
(VREF) on the BD75 board.
2. Press the [
?/1
] button to turn the power on, and select CD
function.
3. Set disc (YEDS-18) and play it.
4. Confi rm that oscilloscope waveform is as shown in the fi gure
4. Confi rm that oscilloscope waveform is as shown in the fi gure
below (eye pattern).
A good eye pattern means that the diamond shape (
◊) in the
center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.1 ± 0.4 Vp-p
Checking Location:
CL117 (VREF)
CL102 (RFOUT)
IC101
– BD75 Board (Conductor Side) –
MECHANISM DECK CHECK MODE
For the mechanism deck check mode, two modes of disc table
mode and loading mode are available.
In the mechanism deck check mode, the disc table turning time
and the loading time in each section are measured and displayed.
mode and loading mode are available.
In the mechanism deck check mode, the disc table turning time
and the loading time in each section are measured and displayed.
Procedure:
Disc table mode:
Press three buttons of [x], [ENTER] and [DISC 4] simultaneously.
Loading mode:
Press three buttons of [x], [ENTER] and [DISC 5] simultaneously.
Disc table mode:
Press three buttons of [x], [ENTER] and [DISC 4] simultaneously.
Loading mode:
Press three buttons of [x], [ENTER] and [DISC 5] simultaneously.
Display contents
Mode
Check command
Display
Disc table mode
(Table turning time
measurement)
0: Right one turn
1: Left one Turn
2: Measurement end
1: Left one Turn
2: Measurement end
r
L
r
L
r
5.7
5.6
5.7
5.6
5.7
3: Undefi ned
Table mode
(Loading time
measurement)
measurement)
4: Star position
5: Open → Close
6: Close → BU up
7: BU up → EX open
8: EX open → EX close
9: EX close → BU down
A: BU down → Open
FF: Measurement end
5: Open → Close
6: Close → BU up
7: BU up → EX open
8: EX open → EX close
9: EX close → BU down
A: BU down → Open
FF: Measurement end
Sta
Clo
UP
Eop
ECL
don
oPn
CLo
Clo
UP
Eop
ECL
don
oPn
CLo
– –.–
1.9
0
1.8
2.0
0.4
1.5
1.9
1.9
0
1.8
2.0
0.4
1.5
1.9
Display is changed by pressing the [DISPLAY] button.
Releasing method:
Press the [
Press the [
?/1
] button to turn the power off.
Click on the first or last page to see other CDP-CE500 service manuals if exist.