Read Sony BDV-E300 / BDV-E801 / BDV-T10 / BDV-T11 / HCD-E300 / HCD-E301 / HCD-E801 / HCD-T10 / HCD-T11 Service Manual online
HCD-E300/E801/T10/T11
16
2-3. Cold Reset
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the set to
the customers.
Procedure:
1. Enter the test menu.
2. Press the [
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the set to
the customers.
Procedure:
1. Enter the test menu.
2. Press the [
M
]/[
m
] buttons on the remote commander to select
the “COLD RESET”, and press the [
3
] button on the remote
commander.
3. The message “COLD RESET” appears on the fluorescent indi-
cator tube, then becomes standby states.
2-4. BD Service
This mode describes details in “3. BD SERVICE MODE” (page
17).
This mode describes details in “3. BD SERVICE MODE” (page
17).
2-5. Tuner Factory Preset
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-6. Digital Media Port Test
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-7. Test Tone Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-8. VACS Display
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-9. VACS On/off
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-10. DSP Halt Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-11. DSP Status Display
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-12. A.CAL Test Disp
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-13. Sircs
Disable
Not used for the servicing.
Press the [
Press the [
?/1
] button if having entered this mode.
2-14. DMPORT Device Test
Procedure:
1. Connect the DMPORT device to this set.
2. Enter the test menu.
3. Press the [
Procedure:
1. Connect the DMPORT device to this set.
2. Enter the test menu.
3. Press the [
M
]/[
m
] buttons on the remote commander to select
the “DMPORT TEST”, and press the [
3
] button on the remote
commander.
4. The DMPORT device enter to the test mode. The operation of
the test mode is different according to each device.
Example of connecting TDM-20iP:
When it enters the test mode and some button operations are
done, the software version is displayed by blinking LED.
done, the software version is displayed by blinking LED.
X . X X: software version
second digit of minor version
fi rst digit of minor version
major
version
LED blinks every 0.2 seconds, and LED is turned off for 0.7
seconds afterwards. The blinking frequency at this time shows
the majors version.
seconds afterwards. The blinking frequency at this time shows
the majors version.
Next, LED blinks every 0.2 seconds, and LED is turned off
for 0.7 seconds afterwards. The blinking frequency at this time
shows the fi rst digit of minor version.
for 0.7 seconds afterwards. The blinking frequency at this time
shows the fi rst digit of minor version.
Next, LED blinks every 0.2 seconds, and LED is turned off
for 0.7 seconds afterwards. The blinking frequency at this time
shows the second digit of minor version.
for 0.7 seconds afterwards. The blinking frequency at this time
shows the second digit of minor version.
Then, it returns to the state that LED blinks.
5. To release from this mode, press the [
?/1
] button.
2-15. S-AIR Test Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-16. S-AIR Radio Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-17. S-AIR ID Change Mode
Procedure:
1. Install a wireless transmitter in this set, and communicate with
Procedure:
1. Install a wireless transmitter in this set, and communicate with
the device for the S-AIR communication.
2. Enter the test menu.
3. Press the [
3. Press the [
M
]/[
m
] buttons on the remote commander to select
the “SAIR ID”, and press the [
3
] button on the remote com-
mander.
4. The S-AIR ID is changed, and release from the test menu.
2-18. EXTRACT ID Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-19. DMPORT Read Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-20. DMPORT Write Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-21. S-Master Setting Switch Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-22. Parental Reset Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-23. CD Repeat Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-24. S-AIR Delay Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-25. DSP Sampling Frequency Display Mode
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
Click on the first or last page to see other BDV-E300 / BDV-E801 / BDV-T10 / BDV-T11 / HCD-E300 / HCD-E301 / HCD-E801 / HCD-T10 / HCD-T11 service manuals if exist.