Read Sony AIR-A10R Service Manual online
AIR-A10R
3
SECTION 2
TEST MODE
COLD RESET
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the three buttons [
x
], [
X
] and [
?/1
] simultaneously.
3. The message “RESET” appears on the liquid crystal display,
then turn the power off.
PANEL TEST MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the three buttons [DISPLAY], [
N
] and [S-AIR CH –]
simultaneously.
3. When the panel test mode is activated, all segments of the liq-
uid crystal display are lighted up.
4. In the state of step 3, press the [DISPLAY] button, and the
model name and destination are displayed on the liquid crystal
display. When the [PRESET +] button is pressed, the date and
the microcomputer version are displayed on the liquid crystal
display.
display. When the [PRESET +] button is pressed, the date and
the microcomputer version are displayed on the liquid crystal
display.
5. In the state of step 3, press the [PRESET –] button, and “KEY
0” is displayed on the liquid crystal display.
“KEY 0” value increases whenever a button on the set is
pressed. However, once a button has been pressed, it is no lon-
ger taken into account.
ger taken into account.
All buttons on the set is pressed, “OK” and “KEY 10” are al-
ternately displayed on the liquid crystal display.
ternately displayed on the liquid crystal display.
6. To release from this mode, press the three buttons [DISPLAY],
[
N
] and [S-AIR CH –] simultaneously.
REMOTE DISABLE MODE
Procedure:
1. In the standby state, while pressing the [S-AIR CH +] button,
Procedure:
1. In the standby state, while pressing the [S-AIR CH +] button,
press the [
?/1
] button to turn the power on.
2. The message “REMOTE ON” or “REMOTE OFF” appears
on the liquid crystal display, and on/off of the remote control
changes.
changes.
S-AIR TEST MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. While pressing the [S-AIR CH +] and [S-AIR CH –] buttons,
press the [PRESET +] button.
3. The message “I2C” appears on the liquid crystal display and
enter the S-AIR test mode.
4. Press the [
N
] button to select the “I2C”, and press the [
N
]
button.
The message “OK” or “NG” appears on the liquid crystal dis-
play and the connection of the I2C line between DARR and
micro controller can be confi rmed.
play and the connection of the I2C line between DARR and
micro controller can be confi rmed.
“OK” : Connection OK.
“NG” : Connection NG.
Press the [
N
] button, return to item selection screen.
5. Press the [PRESET +] button to select the “QUALITY”, and
press the [
N
] button.
The quality of the communication is displayed on the liquid
crystal display.
crystal display.
Press the [
N
] button, return to item selection screen.
6. Press the [PRESET +] button to select the “POWER”, and
press the [
N
] button.
The output power is displayed on the liquid crystal display. In
this state, whenever the [PRESET +] and [PRESET –] buttons
are pressed, the output power can be changed.
this state, whenever the [PRESET +] and [PRESET –] buttons
are pressed, the output power can be changed.
Press the [
N
] button, return to item selection screen.
7. Press the [PRESET +] button to select the “VER.CHECK”,
and press the [
N
] button.
The microcomputer version last updated date of the S-AIR de-
vice connected with this set is displayed on the liquid crystal
display.
vice connected with this set is displayed on the liquid crystal
display.
Press the [
N
] button, return to item selection screen.
8. Press the [PRESET +] button to select the “DARR”, and press
the [
N
] button.
The settings of DARR are displayed on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the displayed setting of DARR can be changed.
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the displayed setting of DARR can be changed.
“CO XXXX” : Connect code display.
“ADR XX”
: Address display.
Press the [
N
] button, return to item selection screen.
9. Press the [PRESET +] button to select the “ANT SET”, and
press the [
N
] button.
The setting of antenna transceiving is displayed on the liquid
crystal display. Whenever the [PRESET +] and [PRESET –]
buttons are pressed, the setting of antenna transceiving can be
changed.
crystal display. Whenever the [PRESET +] and [PRESET –]
buttons are pressed, the setting of antenna transceiving can be
changed.
Press the [
N
] button, return to item selection screen.
10. Press the [PRESET +] button to select the “ANT MON”, and
press the [
N
] button.
The antenna under use is displayed on the liquid crystal dis-
play.
play.
Press the [
N
] button, return to item selection screen.
11. Press the [PRESET +] button to select the “REC”, and press
the [
N
] button.
Whether the audio source that has been reproduced can be re-
corded is displayed on the liquid crystal display.
corded is displayed on the liquid crystal display.
Press the [
N
] button, return to item selection screen.
12. Press the [PRESET +] button to select the “DEMO”, and press
the [
N
] button.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
“ON” : Demo mode (Mode for demonstration at shops).
“OFF” : Normal mode.
Press the [
N
] button, return to item selection screen.
13. Press the [PRESET +] button to select the “RF CHG”, and
press the [
N
] button.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
“ON” : The RF CHG function of DARR is on.
“OFF” : The RF CHG function of DARR is off.
Press the [
N
] button, return to item selection screen.
14. Press the [PRESET +] button to select the “NACK SEND”,
and press the [
N
] button.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] buttons are
pressed, the on/off can be changed.
“ON” : NACK is transmitted at the Bad_Sync.
“OFF” : NACK is not transmitted at the Bad_Sync.
Press the [
N
] button, return to item selection screen.
15. To release from this mode, press the [
?/1
] button. The setting
is maintained until turning off power.
Click on the first or last page to see other AIR-A10R service manuals if exist.