Read Sharp VC-ME80HM (serv.man7) User Guide / Operation Manual online
8
INSTALLING YOUR VCR
AUTO INSTALLATION
5.
SAT RECEIVER
SAT CONTROL
ON
OFF
➝
INPUT
RFIN
L2
SAT NO.
001
PLEASE CONNECT . . .
SAT
L2
VCR
_ _ _ _ _ _ _ _ _
➞
:
SELECT
: CHANGE
SET: ENTER MENU: EXIT
VCR RESET
1. Press STOP to switch on the VCR.
2. Press and hold MENU and CHANNEL
2. Press and hold MENU and CHANNEL
buttons together on the front of the VCR for
10 seconds.
10 seconds.
3. The AUTO INSTALLATION screen should
now be showing on your TV. Press SET to
confirm.
confirm.
4.● Press [
] to select your language
and press SET.
●
Press [
] to select the country of
use and press SET.
●
Ensure your AERIAL/SCART cable is
connected to your VCR and then press
SET to confirm.
connected to your VCR and then press
SET to confirm.
5. SAT CONTROL will be highlighted.
●
If you
do
have a satellite receiver connected
to the VCR continue from point 6.
●
If you
do not
have a satellite receiver
connected to the VCR leave SAT
CONTROL set to OFF and press SET.
CONTROL set to OFF and press SET.
/
/
▲ ▼
The VCR will attempt to copy the TV preset list (NexTView, Smart Link, Easy Link and
Megalogic compatible TV’s only). During the copying process the display will show the TV
presets that are being copied. If the VCR is unable to copy the TV preset list the terrestrial
channels will be automatically installed. (Auto install may take a few minutes.) On
completion the MOVE menu will appear showing the preset channel order. Press MENU to
exit. If the clock is not automatically set, the clock screen will appear, refer to MANUALLY
SETTING THE CLOCK. To check the clock has been set correctly, press DISPLAY until the
time appears on the display. If you wish to customise the channel order refer to MANUALLY
SORTING CHANNELS.
Megalogic compatible TV’s only). During the copying process the display will show the TV
presets that are being copied. If the VCR is unable to copy the TV preset list the terrestrial
channels will be automatically installed. (Auto install may take a few minutes.) On
completion the MOVE menu will appear showing the preset channel order. Press MENU to
exit. If the clock is not automatically set, the clock screen will appear, refer to MANUALLY
SETTING THE CLOCK. To check the clock has been set correctly, press DISPLAY until the
time appears on the display. If you wish to customise the channel order refer to MANUALLY
SORTING CHANNELS.
Points 6-11. (Satellite/Cable Box Control only)
6.Select Channel 1 on your satellite receiver.
7. Press [
6.Select Channel 1 on your satellite receiver.
7. Press [
] to set SAT CONTROL to ON.
8. Press [
] to select INPUT. L2 will be highlighted. If the VCR is not connected to
the satellite receiver as shown previously.......
(i) Your satellite receiver should be connected to the Antenna (RF in on the back of the
(i) Your satellite receiver should be connected to the Antenna (RF in on the back of the
VCR) select RF IN using [
]. You will now need to tune the VCR into the
Satellite receiver channel.
(ii) Press [
] to select CHANNEL.
(iii)Press [
]. The current channel will be displayed as a background to the on-screen
display. If this is not a satellite channel press [
]again. Continue until you see a
satellite channel.
/
/
/
/
All the programmes should now be correctly tuned in and the clock set.
▲
▼
ME-80 HM 7/12/98 12:15 pm Page 8
Click on the first or last page to see other VC-ME80HM (serv.man7) service manuals if exist.