Read Sharp LC-32P70E (serv.man39) User Guide / Operation Manual online
32
• Check if you pressed B on the remote control unit. (See page 8.)
If the indicator on the TV lights up red, press B.
• Is the AC cord disconnected? (See page 4.)
• Check if you pressed a on the TV. (See page 8.)
• Check if you pressed a on the TV. (See page 8.)
• External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off, or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
• Are batteries inserted with polarity (e, f) aligned? (See page 5.)
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated to remote control sensor?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated to remote control sensor?
• Is the image position correct? (See page 18.)
• Are screen mode adjustments (4:3 Mode/WSS) such as picture size made
• Are screen mode adjustments (4:3 Mode/WSS) such as picture size made
correctly? (See pages 18 and 20.)
• Adjust the picture tone. (See pages 13 and 14.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the colour system setting. (See pages 16 and 19.)
• Check the HDMI Setup setting. (See page 19.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the colour system setting. (See pages 16 and 19.)
• Check the HDMI Setup setting. (See page 19.)
• The unit’s internal temperature has increased.
Remove any objects blocking vent or clean.
• Check the power control setting. (See page 15.)
• Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.
• Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.
• Is connection to other components correct? (See pages 9 and 10.)
• Is input signal type selected correctly after connection? (See page 19.)
• Is the correct input source selected? (See page 9.)
• Is non-compatible signal being input? (See page 33.)
• Is picture adjustment correct? (See pages 13 and 14.)
• Is the antenna connected properly? (See page 4.)
• Is “On” selected in “Audio Only”? (See page 18.)
• Is input signal type selected correctly after connection? (See page 19.)
• Is the correct input source selected? (See page 9.)
• Is non-compatible signal being input? (See page 33.)
• Is picture adjustment correct? (See pages 13 and 14.)
• Is the antenna connected properly? (See page 4.)
• Is “On” selected in “Audio Only”? (See page 18.)
• Is the volume too low? (See pages 6 and 7.)
• Make sure that headphones are not connected. (See page 7.)
• Check if you pressed e on the remote control unit. (See page 6.)
• Make sure that headphones are not connected. (See page 7.)
• Check if you pressed e on the remote control unit. (See page 6.)
• Check if “Monochrome” is set to “On”. If so, set it to “Off”. (See page 14.)
Troubleshooting
Appendix
IMPORTANT NOTE ON RESETTING THE PIN
We suggest that you remove the following instruction from the operation manual to prevent children from
reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in
a safe space for future reference.
reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in
a safe space for future reference.
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near
a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: –20°C to e60°C.
Storage temperature: –20°C to e60°C.
1
Repeat steps 1 to 3 in Changing the PIN. (See page 17.)
2
Enter “3001” to cancel out the current PIN.
• The PIN resets to the factory preset “1234”.
Problem
Possible Solution
• No power.
• Unit cannot be operated.
• Remote control unit does not
operate.
• Picture is cut off.
• Strange colour, light colour, or
dark, or colour misalignment.
• Power is suddenly turned off.
• No picture.
• No sound.
• The DTV menu screen is
displayed in monochrome and
hard to select the item.
hard to select the item.
LC-26P70E_GB_f
06.5.2, 6:42 AM
32
Click on the first or last page to see other LC-32P70E (serv.man39) service manuals if exist.