Read Sharp LC-32GD7E (serv.man5) User Guide / Operation Manual online
13
Enter the appropriate channel number with the numeric buttons.
The corresponding bandwidth 7 or 8 MHz is set depending on the
channel and country.
Notes:
You should only adapt the bandwidth if the channel spacing of the
stations in your area deviate from the standard.
If you receive a digital station, the signal quality (“C/N”) and the
signal strength level is displayed by a black bar/numeric value.
The antenna alignment or position is at an optimum when as high
a value as possible (large bar) is displayed for the signal quality
and signal strength.
Align the antenna to a maximum numeric value/bar.
If no signal is found in the set channel, you can start the frequency
search within the selected band (VHF or UHF) by pressing the blue
button.
The manual setup does not work with DVB-T stations in UK.
Check other channels on which digital stations are broadcast terrestri-
ally in your area one after another.
Align the antenna using the weakest station to as maximum as possib-
le a bar/numeric value.
Note: After the antenna has been positioned and aligned, we recommend
the “Automatic station programming” function to search for all stations
(see page 11).
New station search
This function is of particular advantage if you are only searching for new
stations.
Switch on your TV and if no menu is displayed, call the “TV-menu” by
pressing the MENU button on the remote control
Select the ”Setup” item and confi rm with OK.
Select the ”Setup” item and confi rm with OK.
Note:
If you use an active terrestrial antenna, this requires a supply voltage
(5 Volt). See page 9 under "Antenna".
Select “Stations” and confi rm with OK.
Select “Search wizard” and confi rm with OK.
Select “Stations” and confi rm with OK.
Select “Search wizard” and confi rm with OK.
You will get a table for the automatic station search.
If required select “Change search settings” and confi rm with OK. Fol-
If required select “Change search settings” and confi rm with OK. Fol-
low the menus. Otherwise continue with step 10.
Initial installation -> Connect antenna(s) for
Antenna/cable (analogue)
Antenna DVB-T
Satellite DVB-S
Satellite DVB-S
(to ANT TV)
(at ANT TV)
(at ANT SAT)
(at ANT SAT)
✓
6.
•
•
•
•
•
•
7.
1.
2.
3.
4.
4.
5.
Select your location and then indicate whether you are searching via
antenna/cable (analog), antenna DVB-T or in the satellite range (DVB-
S) by marking the appropriate selection with the yellow button.
In DVB-T you can select a channel search (fast station search) or a
frequency search.
Indicate whether you wish to have all stations or only new ones
Indicate whether you wish to have all stations or only new ones
searched for.
Notes:
The frequency search option is to be preferred only in exceptional
cases such as in the event of deviations from the standardized
channels.
If you have purchased a CI module, please insert it as described on
page 10.
Which of the stations of the provider you can watch in the end
depends on which station package you have bought.
To extend an existing station list we recommend you to activate
the option search and store “new stations only”.
Confi rm your selection with OK.
Specify from which station place onwards the stations are to be stored
Specify from which station place onwards the stations are to be stored
and confi rm with OK.
Select “Start search” and confi rm with OK.
Select “Start search” and confi rm with OK.
The station search may take some time.
Do not make any entries or switch off the set during this time.
When the search has ended you will be shown the found and stored sta-
tions sorted in numerical order.
If you also want to search for and store analog stations, repeat the steps
5 to 10.
Select “Analogue” in step 6 and the transmission standard, e.g. “Au-
tom.–BG”.
After the station search has been completed, close the table by pressing
the END button.
Manual station setting
You can also search for and store stations manually. However, detailed
knowledge is necessary for manual programming.
Activate the appropriate menu – depending on whether you want to set
TV or radio stations – in the respective mode (TV or Radio) with the
MENU button.
Select “Setup – Stations” in the TV-menu or “Radio Stations” in the
Select “Setup – Stations” in the TV-menu or “Radio Stations” in the
Radio menu.
Select the entry “Manual tune” and confi rm with OK.
Select the entry “Manual tune” and confi rm with OK.
6.
7.
•
•
•
•
8.
9.
9.
10.
1.
2.
3.
First installation
Click on the first or last page to see other LC-32GD7E (serv.man5) service manuals if exist.