15FS-25H. Tester Download - Sharp TV Specification (repair manual). Page 113

MX-2300/2700 N/G  SIMULATION  7 – 6

44

22

Used to check the toner patch image density level of each color in half tone 
image forming section correction (process correction). (This simulation is used 
to check that the correction is normally executed or not.)

Process

Adjustment/Setup/Operation 
data output/Check (Display/Print)

24

(This simulation is not used in the market.) 
Used to display the process control result.

Process

Adjustment/Setup/Operation 
data output/Check (Display/Print)

25

Used to check the initial condition of process control (half tone correction).

Process

Adjustment/Setup/Operation 
data output/Check (Display/Print)

26

Used to execute the half tone process control forcibly.

Process

Adjustment

27

Used to clear the half tone process control correction value.

Process

Data clear

28

Used to set the timing (ON/OFF) of process control execution.

Process

Setting

29

Enable/disable of the half tone correction during each job is switched.

Process

Setting

31

Used to perform the phase adjustment for OPC drum deflection. (Used to adjust 
the phases of four OPC drums deflection.)

Process (OPC drum)

Adjustment

43

Used to display each developing unit installing state AD value. 
This simulation is added to check the sampling data of the detection judgment of 
developing unit installation not only as the judgment result (trouble display) but 
also as the current state value.

Process (Developing)

Adjustment/Setup/Operation 
data output/Check (Display/Print)

52

(This function is not used. Do not operate.) 
Used to check the toner patch image density level of each color in 1 pixel half 
tone correction. (The simulation is used to check whether the correction is 
normally executed or not.)

Process

Adjustment/Setup/Operation 
data output/Check (Display/Print)

54

(This function is not used. Do not operate.)
Used to display the 1 pixel half tone correction result.

Process

Adjustment/Setup/Operation 
data output/Check (Display/Print)

56

(This function is not used. Do not operate.)
Used to perform the forcible execution of 1 pixel half tone correction.

Process

Setting

57

(This function is not used. Do not operate.)
Used to clear the correction value of 1 pixel half tone correction.

Process

Data clear

46

1

Used to set the default exposure (color copy) for every document mode.

Scanner

Adjustment

2

Used to adjust the exposure in BLACK copy.

Scanner

Adjustment

4

Used to adjust the exposure of the color scanner.

Scanner

Adjustment

5

Used to adjust the exposure of the black scanner.

Scanner

Adjustment

8

Used to make the scanner color balance RGB adjustment (for color push 
scanner mode).

Scanner

Adjustment

9

Used to adjust the exposure.

RSPF

Adjustment

10

Used to the copy density adjustment (manual). (color mode)

Engine

Adjustment

16

Used to the copy density adjustment (manual) [Monochrome, all modes] PG 
print.

Engine

Adjustment

19

Used to set the BLACK auto exposure mode.

Scanner

Adjustment

21

Used to perform the copy color balance manual correction. [Color, All modes]: 
PG print

Engine

Adjustment

23

Used to set ENABLE/DISABLE of the half tone highest density correction.

–

Setting

24

Used to the copy color balance auto adjustment.

Engine

Adjustment

25

Used to execute the fine adjustment of single color mode color balance.

Image process (ICU)

Adjustment

26

Used to reset the single color mode color balance set value to the default.

Image process (ICU)

Adjustment

27

Used to set the engine gamma calculating formula coefficient.

Image process (ICU)

Adjustment

28

(Information on this simulation may be requested in some cases. However, this 
function is basically not used in the market.) 
Used to check the auto exposure/Auto document recognition/ Line number 
recognition (Color mode). If the local memory size is less than 256MB, the 
operation of this simulation may not operate normally.

Image process (ICU)

Adjustment

33

Used to execute the color auto mode adjustment.

Image process (ICU)

Setting

36

Used to perform the fine adjustment of 2-color (Red, Black) copy.

–

Adjustment

37

Used to perform the BLACK image forming adjustment.

–

Adjustment

39

Used to execute the image send sharpness adjustment. (Only when FAX is 
installed)

FAX

Adjustment

40

Used to execute the FAX exposure adjustment. (Collective adjustment of all the 
modes). (Only when FAX is installed)

ICU/FAX

Adjustment

41

Used to execute the FAX exposure adjustment (Normal). (Only when FAX is 
installed)

ICU/FAX

Adjustment

42

Used to execute the FAX exposure adjustment (Fine text). (Only when FAX is 
installed)

ICU/FAX

Adjustment

43

Used to execute the FAX exposure adjustment (Super Fine). (Only when FAX is 
installed)

ICU/FAX

Adjustment

44

Used to execute the FAX exposure adjustment (Ultra Fine). (Only when FAX is 
installed)

ICU/FAX

Adjustment

45

Used to execute the FAX exposure level adjustment and the individual setting 
(600DPI). (Only when FAX is installed)

FAX

Adjustment

47

Used to set the JPEG compression rate in Copy/Scanner (PUSH SCAN).

–

Setting

48

1

Used to execute the magnification adjustment in the scan system (for RSPF).

RSPF/Scanner

Adjustment