Read Sharp XG-NV6XE (serv.man16) Technical Bulletin online
CCE
Sharp Electronics (UK) Ltd., Technical Services Group
How to upgrade the software
[ How to setup the programs ]
1. Extract the tera_nv6.exe (self-extracting file) under new folder.
2. Make the short cut of 'ttpmacro.exe'.
3. Rename this short-cut (from 'ttpmacro.exe') to "Program Transfer".
4. Open the short cut tab in property of this short cut.
5. Add the following words to end of the target.
_/v_fwp2.ttl Note: _ means space.
Target should be
***¥TTPMACRO.EXE /v fwp2.ttl
6. Make the short-cut of 'ttpmacro.exe' once again.
7. Rename this short cut (from 'ttpmacro.exe') to "Check Sum".
8. Open the short cut tab in property of this short cut.
9. Add the following words to end of the target.
_/v_sum2.ttl Note: _ means space.
Target should be
***¥TTPMACRO.EXE /v sum2.ttl
[ How to upgrade the software ]
1. Connect between projector and PC using RS-232C cable.
After connection, turn on projector and PC.
2. Push the key in order of MUTE, MUTE, VOLUME(+), VOLUME(-), ENTER, ENTER and MENU.
Or, Switch the S1-SW from 'NORMAL' to 'WRITE'.
The factory menu will open.
3. In the factory menu, select 'SPECIAL' and push ENTER. Then new menu will appear and select 'IPL' and push
ENTER. After1 or 2 seconds, the lamp and fan will turn off.
4. Execute "Program Transfer" with double click its short-cut and click "Yes".
5. During the software transfer, the message "Transmitting" and the size of transferred program will be displayed on
PC.
6. About 1 minute later, the software transfer will complete and the program will be automatically closed.
Note: Application error occurs every time after transfer completion, but it is OK. Close those error messages.
7. Disconnect the AC cord to finish all procedure.
If S1-SW is in 'WRITE' position, switch it to 'NORMAL'.
[ How to check the software is upgraded properly ]
1. Connect between projector and PC using RS-232C cable.
After connection, turn on projector and PC.
2. Execute "Check Sum" with double click its short-cut.
3. The message "Power On and Check Sum Start?" will be displayed on PC. Then, click "yes".
4. When the new software (0806 version) is installed properly, the "AA8B" will be displayed on PC as shown in the
below. If it is not displayed at first try, please retry the above step.
1. Extract the tera_nv6.exe (self-extracting file) under new folder.
2. Make the short cut of 'ttpmacro.exe'.
3. Rename this short-cut (from 'ttpmacro.exe') to "Program Transfer".
4. Open the short cut tab in property of this short cut.
5. Add the following words to end of the target.
_/v_fwp2.ttl Note: _ means space.
Target should be
***¥TTPMACRO.EXE /v fwp2.ttl
6. Make the short-cut of 'ttpmacro.exe' once again.
7. Rename this short cut (from 'ttpmacro.exe') to "Check Sum".
8. Open the short cut tab in property of this short cut.
9. Add the following words to end of the target.
_/v_sum2.ttl Note: _ means space.
Target should be
***¥TTPMACRO.EXE /v sum2.ttl
[ How to upgrade the software ]
1. Connect between projector and PC using RS-232C cable.
After connection, turn on projector and PC.
2. Push the key in order of MUTE, MUTE, VOLUME(+), VOLUME(-), ENTER, ENTER and MENU.
Or, Switch the S1-SW from 'NORMAL' to 'WRITE'.
The factory menu will open.
3. In the factory menu, select 'SPECIAL' and push ENTER. Then new menu will appear and select 'IPL' and push
ENTER. After1 or 2 seconds, the lamp and fan will turn off.
4. Execute "Program Transfer" with double click its short-cut and click "Yes".
5. During the software transfer, the message "Transmitting" and the size of transferred program will be displayed on
PC.
6. About 1 minute later, the software transfer will complete and the program will be automatically closed.
Note: Application error occurs every time after transfer completion, but it is OK. Close those error messages.
7. Disconnect the AC cord to finish all procedure.
If S1-SW is in 'WRITE' position, switch it to 'NORMAL'.
[ How to check the software is upgraded properly ]
1. Connect between projector and PC using RS-232C cable.
After connection, turn on projector and PC.
2. Execute "Check Sum" with double click its short-cut.
3. The message "Power On and Check Sum Start?" will be displayed on PC. Then, click "yes".
4. When the new software (0806 version) is installed properly, the "AA8B" will be displayed on PC as shown in the
below. If it is not displayed at first try, please retry the above step.
OK
OK
........
00000000 - 00079918
AA8B
OK
.....................
00140000 - 00280000
B93C
OK
........
00000000 - 00079918
AA8B
OK
.....................
00140000 - 00280000
B93C
Click on the first or last page to see other XG-NV6XE (serv.man16) service manuals if exist.