Read Sharp XG-MB70X (serv.man26) User Guide / Operation Manual online
-4
Standby
Power ON
Power Status
Projector Status
Power ON
Power Status
Projector Status
Lamp Status
Volume (0-60)
AV Mute : OFF
AV Mute : ON
Keystone (-127 ~ +127)
INPUT1 (RGB1)
INPUT2 (RGB2)
Volume (0-60)
AV Mute : OFF
AV Mute : ON
Keystone (-127 ~ +127)
INPUT1 (RGB1)
INPUT2 (RGB2)
Freeze : ON
Freeze : OFF
Auto Sync Start
INPUT3 (Video)
INPUT4 (S-Video)
INPUT4 (S-Video)
_ _ _ 0
_ _ _ 1
? ? ? ?
_ _ _ 1
_ _ _ 1
? ? ? ?
_ _ _ 1
_ _ _ 1
_ _ * *
_ _ _ 0
_ _ _ 1
* * * *
_ _ _ 1
_ _ _ 2
_ _ _ 1
_ _ _ 2
_ _ _ 0
_ _ _ 1
_ _ _ 1
_ _ * *
_ _ _ 0
_ _ _ 1
* * * *
_ _ _ 1
_ _ _ 2
_ _ _ 1
_ _ _ 2
_ _ _ 0
_ _ _ 1
_ _ _ 1
P O W R
P O W R
P O W R
T A B N
P O W R
P O W R
T A B N
T L P S
V O L A
I M B K
I M B K
I M B K
K E Y S
I R G B
I R G B
I R G B
I
I
V E D
I
V E D
F R E Z
F R E Z
A D J S
F R E Z
A D J S
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
0 : Standby, 1 : ON
0 : Standby, 1 : ON
0 : OFF, 1 : ON, 2 : Retry, 3 : Waiting, 4 : Lamp Error
0 : Normal, 1 : Temp High, 2 : Fan Err, 8 : Lamp 5% or less,
16 : Lamp Burnt-out, 32 : Lamp Not Ignition Failure,
64 : Temp Abnormally High
16 : Lamp Burnt-out, 32 : Lamp Not Ignition Failure,
64 : Temp Abnormally High
Control Contents
Return
Command
Parameter
Return code (
0DH
)
C1 C2 C3 C4 P1 P2 P3 P4
Response code format
Normal response
Problem response (communication error or incorrect command)
O K
E R R
Command 4-digit
Parameter 4-digit
Command format
Return code (
0DH
)
Return code (
0DH
)
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
commercially available) to the projector. (See page
commercially available) to the projector. (See page
27
of the projector’s operation manual for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate*: 9,600 bps / 115,200 bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
*Set the projector’s baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
the projector processes the command from the computer, it sends a response code to the computer.
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
• If more than one command will be sent to the projector, wait for projector reply before sending next com-
mand.
Note
• Use “POWR????” and “TLPS___1” for projector polling.
• When the projector receives these commands, the on-screen display will not disappear and these com-
• When the projector receives these commands, the on-screen display will not disappear and these com-
mands will not reset the “Auto Power Off” function timer when no signal is present.
Commands
Example: When turning on the projector, make the following setting.
RS-232C Specifications and Commands
→
←
←
P
O
W
R
_
1
_
_
O
K
Projector
Computer
XG-MB70X_E_P02_19.p65
04.8.6, 2:23 PM
4
Click on the first or last page to see other XG-MB70X (serv.man26) service manuals if exist.