Read Sharp XG-C465X (serv.man4) Service Manual online
XG-C435X/C465X
3 – 8
8
Black level/amplitude
adjustment of LCD
panel input signal
adjustment of LCD
panel input signal
1) Select the following.
Group: OUTPUT 1
Adjustment item: G1-BLK
G1-GAIN
R:R1-BLK
R1-GAIN
B:B1-BLK
B1-GAIN
Adjustment item: G1-BLK
G1-GAIN
R:R1-BLK
R1-GAIN
B:B1-BLK
B1-GAIN
2) Check that the white pattern for pro-
cess adjustment is displayed.
3) Connect a synchroscope to 2P of
(P1401).
4) For red and blue, connect to (P1401-
1P) and (P1401-3P) respectively.
1) Select G1-GAIN, and adjust the signal amplitude as follows using
the operation SW or button on the remote control (see figure (1)
below).
5.1 Vpp
below).
5.1 Vpp
± 0.05 V
2) Select G1-BLK, and adjust the white-white level as follows using
the operation SW or button on the remote control (see figure (2)
below).
0.5 Vpp
below).
0.5 Vpp
± 0.1 V
3) Adjust red and blue in the same way.
(G waveform diagram of process pattern)
* The part defining the amplitude to the waveform is the same for both
R and B.
R and B.
9
Sample-hold pulse
delay amount adjust-
ment
delay amount adjust-
ment
1) Input the black signal of XGA mode.
2) Select the following.
2) Select the following.
Group: OUTPUT3
Adjustment item: ENBR-DLY
G: ENBG-DLY
B: ENBB-DLY
Adjustment item: ENBR-DLY
G: ENBG-DLY
B: ENBB-DLY
1) Check the blur and ghost of characters of OUTPUT3.
2) Raise the ENBR-DLY value until pre-ghost appears on the left of
2) Raise the ENBR-DLY value until pre-ghost appears on the left of
characters of OSD.
3) When the value is reduced by 1 to 2 points, pre-ghost disappears.
Set to the value reduced by 3 from the value where pre-ghost dis-
appears.
(Set to 16 in the following case: When the ENBR-DLY value is 20,
pre-ghost appears; when it is 19, pre-ghost disappears.)
appears.
(Set to 16 in the following case: When the ENBR-DLY value is 20,
pre-ghost appears; when it is 19, pre-ghost disappears.)
4) Adjust green and blue in the same way.
NOTE: EPSON panels may vary by 1 to 2 points from lot to lot. To
improve the ghost quality, perform this adjustment.
10
RGB counter voltage
adjustment
adjustment
1) Select the following.
Group: OUTPUT1
Adjustment item: R-COM
G-COM
B-COM
R-COM2
G-COM2
B-COM2
Adjustment item: R-COM
G-COM
B-COM
R-COM2
G-COM2
B-COM2
1) Adjust flicker using the operation SW or button on the remote con-
trol so that it becomes minimum.
2) When flicker appears on the screen unevenly, adjust the center
area considering the whole balance.
11
RGB white balance
adjustment
adjustment
1) Input the RGB 50% gray signal.
(XGA60Hz)
2) Select the following.
Group: OUTPUT1
Adjustment item: R1-BLK (R)
B1-BLK (B)
Adjustment item: R1-BLK (R)
B1-BLK (B)
1) 1. Adjust R1-BLK and B1-BLK so that the following chromaticity
values are obtained in the middle of the screen using CL200.
x = 294
x = 294
± 5, y = 327 ± 5
12
sRGB white balance
adjustment
adjustment
1) Input the RGB 50% gray signal.
2) Select the following.
2) Select the following.
Group: OUTPUT1
Adjustment item: S-G1-BLK
S-B1-BLK
Adjustment item: S-G1-BLK
S-B1-BLK
1) Adjust S-G1-BLK and S-B1-BLK so that the following chromaticity
values are obtained in the middle of the screen using CL200.
x = 322
x = 322
± 5, y = 341 ± 5
13
Auto keystone initial-
ization
ization
1) Select the following.
Group: LINE
Adjustment item: Calibration
Adjustment item: Calibration
1) With the set placed on a level surface, press the ENTER key and
check that K-Sensor value is 0
± 3 (125 - 3).
Check that keystone is caused by tilting the unit.
14
Model name writing
1) Write the model name with RS232C
command.
1) C465: MF_10000 (default)
C435: MF_10001
15
Tracking check
1) Input the RGB 10-step gray scale sig-
nal (inversion on top and bottom).
2) Select the following.
Group: OUTPUT3
Adjustment item: GAMMA
Adjustment item: GAMMA
1) Check the lower gradation tracking.
When it is improper, optimize the GAMMA value.
1: Default (normal)
2: Red and blue down
3: Red and blue up
1: Default (normal)
2: Red and blue down
3: Red and blue up
NOTE: When changing the GAMMA value, readjust the white bal-
ance.
16
Auto color shading
correction
correction
1) Perform the auto color shading correc-
tion using the color shading correction
system (ccdc).
system (ccdc).
1) Check that remarkable color shading is not found on the screen.
No.
Adjustment Item
Adjustment Conditions
Adjustment Procedures
White-white (2)
Amplitude (1)
Click on the first or last page to see other XG-C465X (serv.man4) service manuals if exist.