Read Sharp MX-M950 / MX-MM1100 (serv.man40) Service Manual online
MX-M1100 MAINTENANCE 9 – 3
(2) [Maintenance timing] (Framed)
a. Maintenance counters
• After completion of the maintenance, execute Sim. 24-4 (MEIN-
TENANCE ALL clear).
b. Fusing web
• After completion of the maintenance, execute Sim. 24-4 (FUSER
WEB SEND clear).
* When the web unit is not installed, the FK3 code is displayed. In
this case, set the web unit and cancel it with Sim.14. (The FK3
code is deleted, but the web feed counter continues the opera-
tion.)
code is deleted, but the web feed counter continues the opera-
tion.)
(3) [Check the waste toner box.] (Framed)
• After replacing the waste toner bottle with an empty one, close
the front door to cancel the full detection.
4. Maintenance system table
✕: Check (Clean, replace, or adjust as necessary.) {: Clean ▲: Replace U: Adjust ✩: Lubricate : Shift the position
Code
Content
Print job
Enable / Disable
TA
The maintenance counters (total) reaches the
set value of Sim. 21-1, and Sim. 26-38 is set to
Print Disable.
set value of Sim. 21-1, and Sim. 26-38 is set to
Print Disable.
Disable
Code
Content
Print job
Enable / Disable
FK3
When the end detection sensor (WEBED) is
turned ON.
turned ON.
Disable
Code
Content
Print job
Enable / Disable
—
Waste toner full
Disable
Unit name
(Detailed page)
No.
Part name
When
calling
500
K
1000
K
1500
K
2000
K
2500
K
3000
K
Remark
[Refer to the Parts Guide.
Block/Item No.]
(Only the replacement parts
are described.)
Photoconductor
Section (9 - 7)
Section (9 - 7)
1
OPC drum
✕
✕
▲
✕
▲
✕
▲
2
Cleaning blade
✕
▲
▲
▲
▲
▲
▲
[PG No.: [36] - 35]
When replacing, apply stearic acid.
(UKOG-0312FCZZ)
When replacing, apply stearic acid.
(UKOG-0312FCZZ)
3
Sub blade
✕
▲
▲
▲
▲
▲
▲
[PG No.: [36] - 54]
4
Side seal F, R
✕
▲
▲
▲
▲
▲
▲
[PG No.: [36] - 20, [36] - 66]
5
Drum separation pawl
✕
▲ ▲
▲
▲
▲
▲ When replacing, shift the separation
pawl mounting position.
[PG No.: [37] - 2]
[PG No.: [37] - 2]
6
Discharge lamp
✕
{
{
{
{
{
{
7
Procon sensor
✕
{
{
{
{
{
{
8
Surface potential sensor
✕
{
{
{
{
{
{
Hold the sensor so that no foreign
material enters the port of the sensor.
Wipe it with waste cloth. Use alcohol if
it is dirtied with oil.
material enters the port of the sensor.
Wipe it with waste cloth. Use alcohol if
it is dirtied with oil.
9
Cleaning brush roller
✕
{
{
{
{
{
▲
[PG No.: [36] - 61]
10
Charger wire
{
▲
▲
▲
▲
▲
▲
[PG No.: [38] - 25]
11
Screen grid
✕
▲
▲
▲
▲
▲
▲
[PG No.: [38] - 26]
12
Charger cleaner
▲
▲
▲
▲
▲
▲
[PG No.: [38] - 6]
13
Charger cushion
▲
▲
▲
▲
▲
▲
[PG No.: [38] - 6]
14
Duct sheet
▲
▲
▲
▲
▲
▲
[PG No.: [74] - 61]
15
Blade side seal F, R
✕
✕
✕
✕
✕
✕
▲
[PG No.: [36] - 24, [36] - 58]
16
Cleaning brush bearing
✕
17
Cleaning brush drive bearing
✕
18
Separation pawl oscillation
bearing
bearing
✕
19
Auxiliary cleaning brush
bearing
bearing
✕
20
Bearing
✕
21
Separation pawl oscillation arm
✕
22
Separation pawl oscillation
shaft
shaft
✕
23
Ball bearings
✕
24
Gears
✕
25
Cleaner base guide
▲
▲
▲
▲
▲
▲
[PG No.: [38] - 3]
26
Sub blade seal F, R
✕
✕
✕
✕
✕
✕
27
Main charger case
{
{
{
{
{
▲
[PG No.: [38] - 9]
Waste toner section
(9 - 17)
(9 - 17)
1
Waste toner bottle (with cap)
✕
▲
▲
▲
▲
▲
▲
[PG No.: [75] - 26]
2
Gears
✕
3
Bearing(Waste toner resin
bearing)
bearing)
✕
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man40) service manuals if exist.