MX-M950, MX-MM1100 (serv.man38). Section 7 Simulation - Sharp Copying Equipment Service Manual (repair manual). Page 13

MX-M1100  SIMULATION  7 – 13

<Saddle finisher>

 

3-20

Operation test/check

Function (Purpose) Used to check the operations  of the sen-

sors and the detectors in the saddle unit
and the related circuits.

Saddle unit

Operation/Procedure
The operation conditions of the sensors and the detectors are dis-
played.
The sensor and the detector which are turned ON are highlighted.
When [SYSTEM SETTINGS] key is pressed, the screen returns to
the SUB code entry menu.
<Saddle unit>

 

3-21

Operation test/check

Function (Purpose) Used to check the operations of the saddle

unit motor and the control circuit.

Saddle unit

Operation/Procedure
1)

Select a target item of the operation check with the touch panel
key.

2)

Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.

3)

When [SYSTEM SETTINGS] key is pressed, the screen
returns to the SUB code entry menu.

 

3-22

Adjustment

Function (Purpose) Used to adjust the saddle unit.
Section

Saddle unit

Operation/Procedure
1)

Select a target item of the check with [

↑] [↓] keys on the touch

panel.

2)

Enter the set value with 10-key. 
Press [OK] key. (The set value is saved.)

3)

When [SYSTEM SETTINGS] key is pressed, the screen
returns to the SUB code entry menu.

A

Jogger 
position 
adjustment

JOGGER1 (OTHER)

Other

85 - 115

100

[Jogger shift direction (main scanning direction) position 
adjustment]
• Unit of one step: 0.1mm
• Adjustment resolution: 0.5mm
• Actual range: 

±1.5mm

When the set value is smaller (-) than the default value. :
The jogger width becomes smaller than the reference level.

When the set value is greater (+) than the default value. :
The jogger width becomes greater than the reference level.

B

JOGGER1 (A3)

A3

C

JOGGER1 (B4)

B4

D

JOGGER1 (A4R)

A4R

E

JOGGER1 (A4)

A4

F

JOGGER1 (B5R)

B5R

G

JOGGER1 (B5)

B5

H

JOGGER1 (11 

✕ 17)

11 

✕ 17

I

JOGGER1 (8.5 

✕ 14)

8.5 

✕ 14

J

JOGGER1 (8.5 

✕ 11R)

8.5 

✕ 11R

K

JOGGER1 (8.5 

✕ 11)

8.5 

✕ 11

L

JOGGER1 (12 

✕ 18)

12 

✕ 18

M

Bending 
number 
adjustment

BEND ADJ COUNT

Bending number 
adjustment

1 - 30

2

Unit of 1 step: Once
Adjustment resolution: Once
Actual range: 1 - 30 times

1

BLTHPS

Eject HP sensor

2

JOGHPS

Jogger HP sensor

3

STTRYPAP

Staple tray paper presence sensor

4

LFRTDRS

Left front door sensor

5

EXITS

Paper exit sensor

6

PSTRYEXT

Staple paper exit sensor

7

FINENT

Entry port sensor

8

FLDUNEXT

Folding pass sensor

9

FLDCMHP

Folding cam HP sensor

10

FLDPLTHP

Folding plate HP sensor

11

FLDBTMHP

Rear edge fence HP sensor

12

STJCTGHP

Bundle branch open/close HP sensor

1

DRRLVI_M

Drive roller oscillation motor

2

BDJCTG_M

Bundle branch open/close motor

3

BLT_M

Eject  motor

4

JOG_M

Jogger motor

5

EXIT_M

Paper exit motor

6

PORLDR_M

Tapping roller drive motor

7

LOTRS_M

Lower transport motor

8

ENT_M

Entry port motor

9

SDLSTR_M

Center binding stapler rear motor

10

SDLSTF_M

Center binding stapler front motor

11

TALFNC_M

Rear edge fence shift motor

12

FLDROL_M

Folding roller motor

13

FLDPLT_M

Folding plate motor

14

SDLPRS_S

Center binding holding SOL

15

POS_S

Tapping SOL

16

TEGPRS_S

Rear edge holding SOL

17

LOJCTG_S

Lower branch SOL