MX-M950, MX-MM1100 (serv.man38). Section 7 Simulation - Sharp Copying Equipment Service Manual (repair manual). Page 12

MX-M1100  SIMULATION  7 – 12

<Saddle finisher/saddle section: Only when the center binding unit
is installed.>

<Saddle finisher/saddle section: Only when the punch unit is
installed.>

 

3-10

Finisher adjustment

Function (Purpose) Used to adjust the jogger position, the lead

edge stopper position, the staple jogging
count number, and the paper folding count
number.

Finisher

Operation/Procedure
1)

Select a target item of the check with [

↑] [↓] keys on the touch

panel.

2)

Enter the set value with 10-key. 
Press [OK] key. (The set value is saved.)

3)

When [SYSTEM SETTINGS] key is pressed, the screen
returns to the SUB code entry menu.

<Finisher>

17

POS_S

Tapping SOL

18

TEGPRS_S

Rear edge holding SOL

1

SDLPRS_S

Center binding holding SOL

2

BDJCTG_M

Bundle branch open/close motor

3

TALFNC_M

Rear edge fence shift motor

4

SDLSTF_M

Center binding stapler motor: front

5

SDLSTR_M

Center binding staple motor: rear

6

FLDPLT_M

Folding plate motor

7

FLDROL_M

Folding roller motor

8

DRRLVI_M

Drive roller oscillation motor

1

PNCH_M

Punch motor

2

PNCHMV_M

Punch shift motor

3

STSMOV_M

Horizontal resist detection motor

A

Jogger 
position 
adjustment

JOGGER1 (OTHER)

Other

80 - 115

100

[Jogger shift direction (main scanning direction) position 
adjustment]
• Unit of 1 step: 0.1mm
• Adjustment resolution: 0.5mm
• Actual range: -2.0 - 1.5mm

When the set value is smaller (-) than the default value. :
The unit shifts to the direction so that the jogger width 
becomes smaller than the reference level.

When the set value is greater (+) than the default value. :
The unit shifts to the direction so that the jogger width 
becomes greater than the reference level.
* Do not set the value to 80 - 89.

B

JOGGER1 (A3)

A3

C

JOGGER1 (B4)

B4

D

JOGGER1 (A4R)

A4R

E

JOGGER1 (A4)

A4

F

JOGGER1 (B5R)

B5R

G

JOGGER1 (B5)

B5

H

JOGGER1 (11 x 17)

11 x 17

I

JOGGER1 (8.5 x 14)

8.5 x 14

J

JOGGER1 (8.5 x 11R)

8.5 x 11R

K

JOGGER1 (8.5 x 11)

8.5 x 11

L

Alignment 
jogger 
position 
adjustment

JOGGER2 (OTHER)

Other

70 - 130

100

[Alignment unit jogger position adjustment value]
• Unit of 1 step: 0.1mm
• Adjustment resolution: 0.1mm
• Actual range: -3.0 - 3.0mm

When the set value is smaller (-) than the default value. :
The unit shifts to the direction so that the alignment jogger 
width becomes smaller than the reference level.

When the set value is greater (+) than the default value. :
The unit shifts to the direction so that the alignment jogger 
width becomes greater than the reference level.

M

JOGGER2 (A3)

A3

N

JOGGER2 (B4)

B4

O

JOGGER2 (A4R)

A4R

P

JOGGER2 (A4)

A4

Q

JOGGER2 (B5R)

B5R

R

JOGGER2 (B5)

B5

S

JOGGER2 (11 x 17)

11 x 17

T

JOGGER2 (8.5 x 14)

8.5 x 14

U

JOGGER2 (8.5 x 11R)

8.5 x 11R

V

JOGGER2 (8.5 x 11)

8.5 x 11

W

JOGGER2 (A5R)

A5R

X

JOGGER2 (A5)

A5

Y

JOGGER2 (5.5 x 8.5R)

5.5 x 8.5R

Z

JOGGER2 (5.5 x 8.5)

5.5 x 8.5

AA

Lead edge 
stopper 
position 
adjustment

STOPPER

Lead edge 
stopper position 
adjustment

50 - 120

100

[Lead edge stopper position adjustment value]
• Unit of 1 step: 0.1mm
• Adjustment resolution: 0.1mm
• Actual range: -5.0 - 2.0mm

When the set value is smaller (-) than the default value. :
The holding level by the lead edge stopper is decreased.

When the set value is greater (+) than the default value. :
The holding level by the lead edge stopper is increased.

AB

Staple 
jogging count 
number

STAPLE JOGGING COUNT

Staple jogging 
count number

0 - 1

0

Unit of 1 step: Once
Adjustment resolution: Once
Actual range: 1 - 2 times