Read Sharp MX-M266N / MX-M316N / MX-M356N (serv.man3) Service Manual online
MX-M356NV SPECIFICATIONS 2 – 6
*2: Custom size
Long size paper (bypass tray only): support up to 1,200mm by Sim
* Long size paper ejection is from center tray/inner finisher
* Long size paper ejection is from center tray/inner finisher
*3: Comply to “Paper type setting”
*4: Can be input but alignment is not supported
*5: Can be input and stapled but alignment is not supported
*6: Alignment of heavy paper more than 129g/m
*4: Can be input but alignment is not supported
*5: Can be input and stapled but alignment is not supported
*6: Alignment of heavy paper more than 129g/m
2
is not supported
*7: Only front/back cover is available.
*8: Can be fed but not covered under warranty.
*9: A4 paper (grain long) corresponding to 58g/m
*8: Can be fed but not covered under warranty.
*9: A4 paper (grain long) corresponding to 58g/m
2
I. Operation panel
J. Controller board
*1: The USB port can be disabled by Sim
K. Memory/Hard disk/SD card memory
*1: Memory expansion is not available
*2: HDD capacity may vary depending on the procurement condi-
tion.
*2: HDD capacity may vary depending on the procurement condi-
tion.
L. Warm-up time
* Result may change depending on conditions.
*1: Conditions: Leave the machine for 60 sec. after door open,
*1: Conditions: Leave the machine for 60 sec. after door open,
standard condition, Polygon stops.
2. Copy functions
A. First copy time
* Measuring Conditions
Feed the A4 (8-1/2 x 11) sheet in landscape from tray 1, with the
polygon rotating condition.
Value might vary depends on the machine settings/conditions
polygon rotating condition.
Value might vary depends on the machine settings/conditions
B. Job Speed
* Defines the copy speed of when the main unit and a document
feeder are used in combination.
* S to S: copying 1 set of an 11-sheet original in A4 / 8.5" x 11"
(not including the first copy)
Monochrome: 600 x 400dpi (default)
Monochrome: 600 x 400dpi (default)
AB System (mm)
Inch System (inch)
Min.
Max.
Min.
Max.
Bypass tray
X
140
432
5-1/2
17
Y
100
297
5-1/2
11-5/8
Duplex
X
182
432
7-1/4
17
Y
148
297
5-1/2
11-5/8
Size
7 inch
Form
Dot matrix LCD, Touch panel
Display dot number
800 x 480 dots (WVGA)
LCD backlight
LED backlight
LCD contrast adjust
Yes
Angle/position adjustment
No tilting mechanism
CPU
ARM11: 600MHz
ARM9: 400MHz/during 1W energy save mode:
75MHz
ARM9: 400MHz/during 1W energy save mode:
75MHz
Interface
IEEE1284 Parallel
IEEE1284 Parallel
No
Ethernet
1port
Interface
10Base-T, 100Base-TX, 1000Base-T
Support Protocol
TCP/IP (IPv4, IPv6), IPX/SPX, Ether Talk
USB 2.0 (high
speed) (host)*
speed) (host)*
1
2port
(Simultaneous use of the front/rear ports is
enable.)
(Simultaneous use of the front/rear ports is
enable.)
USB 2.0 (high
speed) (device)
speed) (device)
1port
USB-HUB (host)
Internal: 4port
* Main unit USB Front Port
* Main unit USB Rear Port
* Key board USB Port
* IC Card Reader
* Main unit USB Front Port
* Main unit USB Rear Port
* Key board USB Port
* IC Card Reader
Serial I/F
(For coin-operated
machines)
(For coin-operated
machines)
1port
SD card
ICU (Reus) PWB
HDD*
2
Memory*
1
4GB
2GB
OPT (250GB)
Memory area
(SD card)
(SD card)
Boot/Program area
FAX data storage area
FAX data storage area
Without HDD
With HDD
512MB
1GB
Warm-up time
20sec. or less
Pre heat
Yes
Jam recovery time
*1
10sec. or less
Engine
26cpm machine
31cpm machine
35cpm
machine
Scan Speed
31
56
31
56
56
Platen
4.3 sec.
4.3 sec.
4.3 sec.
4.3 sec.
4.0 sec.
RSPF
7.0 sec.
7.0 sec.
7.0 sec.
7.0 sec.
6.7 sec.
Engine
26cpm
machine
31cpm
machine
35cpm
machine
S to S
26cpm (100%)
31cpm (100%)
35cpm (100%)
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N (serv.man3) service manuals if exist.