Read Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual online
MX-M1205 MX-EB15 (MIRRORING KIT) 24 – 1
MX-M1205
Service Manual
[24] MX-EB15 (MIRRORING KIT)
1. Unpacking
A. Packed items check
*1: Not use for this installation.
*2: Not use for this installation. (One of five screws)
NOTE:
Note for installing the mirroring kit
Before installing the mirroring kit, fully understand the descriptions
below and careful follow the instructions.
below and careful follow the instructions.
Prohibited items
When installing a mirroring kit newly, do not install a mirroring kit
which has been used.
which has been used.
When a mirroring kit which has been used is installed in new instal-
lation of the mirroring kit, the mirroring kit HDD will overwrite the
machine HDD which has been original installed, deleting the user
data and causing a freeze of the machine.
lation of the mirroring kit, the mirroring kit HDD will overwrite the
machine HDD which has been original installed, deleting the user
data and causing a freeze of the machine.
“A mirroring kit which has been used” includes one which was only
installed and conducted.
installed and conducted.
When removing the HDD after installing the mirroring kit, be sure to
remove the both HDD’s. If only one HDD is removed and rein-
stalled, the data on the both HDD's data may be out of synchroni-
zation.
remove the both HDD’s. If only one HDD is removed and rein-
stalled, the data on the both HDD's data may be out of synchroni-
zation.
When removing the HDD, first disconnect the HDD SATA connec-
tor of the MFP PWB. This procedure brings the machine into the
state where the both HDD's are disconnected from the machine
simultaneously.
tor of the MFP PWB. This procedure brings the machine into the
state where the both HDD's are disconnected from the machine
simultaneously.
Countermeasures
If a mirroring kit which has been used must be installed at any cost,
delete the mirroring information of the HDD before installing. (For
details, refer to “5. Deleting the HDD mirroring information”
described later.)
delete the mirroring information of the HDD before installing. (For
details, refer to “5. Deleting the HDD mirroring information”
described later.)
2. Data backup
MEMO: When the mirroring kit is installed to a machine which has
not been used, this procedure is not required. Backup of data with
a machine which has been used is made in order to provide against
a failure in automatic copy of data to the HDD of the kit.
not been used, this procedure is not required. Backup of data with
a machine which has been used is made in order to provide against
a failure in automatic copy of data to the HDD of the kit.
1)
Use SIM56-2 or Web Page to backup the HDD data.
(Device cloning data / Storage backup data)
(Device cloning data / Storage backup data)
2)
Use SIM56-3 or Web Page to backup the HDD data.
(Document filing data)
(Document filing data)
3)
Use SIM56-4 or Web Page to backup the HDD data.
(Jog log data (Reinstallation disable))
(Jog log data (Reinstallation disable))
3. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Gain access to the MFP control unit
1)
Remove the screw, and remove the rear cabinet.
No.
Name
Quantity
1
Mirroring HDD unit
1
2
Screw *2
5
3
Step screw
4
4
Damper
4
5
Wire saddle (small size) *1
2
6
Wire saddle (big size)
2
7
Earth plate *1
1
8
Core *1
2
9
SATA cable
2
10
Power cable
1
11
Communication cable
1
12
RAID PWB
1
13
Banding band
1
2
1
3
4
5
8
6
9
10
11
12
13
7
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.