Read Sharp MX-CF11 / MX-6240N / MX-7040N Specification online
MX-CF11 DETAILS 4 – 2
• The 1st tray lift motor switches on to raise the stack until the
actuator enters the pick-up roller unit position sensor again and
switches the lift motor off.
switches the lift motor off.
• This cycle repeats until the end of the job or until paper runs out.
B. PAPER NEAR END/PAPER END
When feed starts with a full tray, the actuator [A] on the rotating
shaft of the bottom plate lift arm [B] is at the 1st tray lower limit sen-
sor [C].
As paper feeds and the stack grows smaller, the lift arm rises and
the actuator descends until the actuator reaches the 1st tray upper
limit sensor [D]. At this time the operation panel signals near-end
for the 1st tray.
When the last sheet feeds, the paper feed sensor, a photosensor
(not shown) signals that paper has run out.
shaft of the bottom plate lift arm [B] is at the 1st tray lower limit sen-
sor [C].
As paper feeds and the stack grows smaller, the lift arm rises and
the actuator descends until the actuator reaches the 1st tray upper
limit sensor [D]. At this time the operation panel signals near-end
for the 1st tray.
When the last sheet feeds, the paper feed sensor, a photosensor
(not shown) signals that paper has run out.
C. PAPER SIZE DETECTION
The side fences (1) and (2) can be adjusted to standard and non-
standard paper sizes.
When the side fences are moved to match the paper width, a feeler
[A] slides along the wiring patterns on the paper width switch termi-
nal plate [B].
The combination of the following two factors determines the paper
size:
• The position where the feeler activates the terminal
• The status of the paper length sensor [C] (ON or OFF).
The paper end sensor [D] de-activates when the last sheet is fed
and reports that the paper tray is empty.
The paper size is detected by six sensors whose combined read-
ings are used to detect the following paper sizes.
standard paper sizes.
When the side fences are moved to match the paper width, a feeler
[A] slides along the wiring patterns on the paper width switch termi-
nal plate [B].
The combination of the following two factors determines the paper
size:
• The position where the feeler activates the terminal
• The status of the paper length sensor [C] (ON or OFF).
The paper end sensor [D] de-activates when the last sheet is fed
and reports that the paper tray is empty.
The paper size is detected by six sensors whose combined read-
ings are used to detect the following paper sizes.
(Yes) Width and length sensors can detect paper sizes automati-
cally.
(*) Accurate paper size detection requires setting with the "Tray
Paper Setting" key on the operation panel.
(H) 5V
(L) 0V
cally.
(*) Accurate paper size detection requires setting with the "Tray
Paper Setting" key on the operation panel.
(H) 5V
(L) 0V
[A]
[B]
[D]
[C]
[A]
[B]
[C]
[D]
(1)
(2)
Paper Size Detection Bits
Area
Paper Size
W1
W2
W3
W4
W5
L1
NA
EU
Large
Size
Size
12×18 in.
H
H
H
H
L
L
YES
YES
Large
Size
Size
13×19 in.
H
H
H
H
L
L
*
*
Large
Size
Size
320×450 mm
H
H
H
H
L
L
*
*
A3
SEF
SEF
297×420 mm
H
H
H
L
L
L
YES
YES
A4LEF
297×210 mm
H
H
H
L
L
H
YES
YES
DLT
SEF
SEF
11×17 in.
H
H
H
L
H
L
YES
YES
LT LEF
11×8
1
/
2
in.
H
H
H
L
H
H
YES
YES
B4
SEF
SEF
257×364 mm
H
H
L
L
H
L
YES
YES
B5
LEF
LEF
257×182 mm
H
H
L
L
H
H
YES
YES
A4
SEF
SEF
210×297 mm
H
H
L
H
H
L
YES
YES
LT
SEF
SEF
8
1
/
2
×11 in.
H
H
L
H
H
L
YES
*
A5LEF
210×148 mm
H
H
L
H
H
H
*
YES
HLT
LEF
LEF
8
1
/
2
×5
1
/
2
in.
H
H
L
H
H
H
YES
*
B5
SEF
SEF
182×257 mm
H
L
L
H
H
L
*
*
F SEF
8×13 in.
H
L
L
H
H
L
YES
YES
A5
SEF
SEF
148×210 mm
H
L
H
H
H
H
YES
YES
HLT
SEF
SEF
5
1
/
2
×8
1
/
2
in.
L
L
H
H
H
H
YES
YES
Click on the first or last page to see other MX-CF11 / MX-6240N / MX-7040N service manuals if exist.