Read Sharp MX-B381 / MX-B401 (serv.man8) Service Manual online
MX-B381/B401 DEHUMIDIFIER HEATER KIT (SERVICE PARTS) FOR THE MX-CSX1/CSX2 14 – 3
D. Install the desk dehumidifier heater unit to the
MX-CSX1.
* The descriptions are made on the MX-CSX1. If the MX-CSX2 is
also installed, perform the same procedures for the MX-CSX2.
1)
Pass the desk dehumidifier heater harness through the MX-
CSX1 to the rear side.
CSX1 to the rear side.
2)
Attach the desk dehumidifier heater to the upper side of the
MX-CSX1, and fix it with the M4 x 10P tight screw (No.5).
MX-CSX1, and fix it with the M4 x 10P tight screw (No.5).
3)
Pass the desk dehumidifier heater harness through the mini
clamp. (2 positions)
clamp. (2 positions)
4)
Pass the desk dehumidifier heater harness through the 500
hole of the desk dehumidifier heater similarly with C-1).
hole of the desk dehumidifier heater similarly with C-1).
5)
Insert the connector of the desk dehumidifier heater harness
into CN-B of the heater interface PWB.
into CN-B of the heater interface PWB.
E. Connection with the MX-CSX1 and the MX-
CSX2 (Connection of the first stage and the
second stage, and connection of the second
stage and the third stage)
second stage, and connection of the second
stage and the third stage)
* The WH Frontier I/F harness is not used.
* When the MX-CSX2 is not installed, this procedure is not
* When the MX-CSX2 is not installed, this procedure is not
required.
The connection procedures are described on connection between
the MX-CSX1 and the MX-CSX2. When two units of the MX-CSX2
are installed, first connect the MX-CSX1 and the MX-CSX2, then
connect the MX-CSX2 (upper stage) and the MX-CSX2 (lower
stage).
1)
the MX-CSX1 and the MX-CSX2. When two units of the MX-CSX2
are installed, first connect the MX-CSX1 and the MX-CSX2, then
connect the MX-CSX2 (upper stage) and the MX-CSX2 (lower
stage).
1)
Pass the white connector of the WH desk I/F harness (No.6)
through the square hole in the MX-CSX1 to the heater inter-
face PWB side.
through the square hole in the MX-CSX1 to the heater inter-
face PWB side.
2)
Pass the red connector of the WH desk I/F harness through
the square hole in the MX-CSX2 to the heater interface PWB
side.
the square hole in the MX-CSX2 to the heater interface PWB
side.
3)
Hang the harness on the notch of the cabinet of the MX-CSX1.
4)
Insert the white connector of the WH desk I/F harness into CN-
C of the heater interface PWB of the MX-CSX1.
C of the heater interface PWB of the MX-CSX1.
5)
Insert the red connector of the WH desk I/F harness into CN-A
of the heater interface PWB of the MX-CSX2.
of the heater interface PWB of the MX-CSX2.
1)
2)
3)
4)
5)
Click on the first or last page to see other MX-B381 / MX-B401 (serv.man8) service manuals if exist.