Read Sharp MX-6500N / MX-7500N (serv.man20) Service Manual online
MX-7500N SIMULATION 6 – 11
3-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select the item to be checked with the touch panel key.
2) Press [EXECUTE] key.
1) Select the item to be checked with the touch panel key.
2) Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
When [EXECUTE] key is pressed, the operation is terminated.
Finisher (100-sheet stapling)
*1: Operates only when the transport unit is installed.
Saddle stitch finisher (100-sheet stapling)
Folding unit (100-sheet stapling)
Trimming module (100-sheet stapling)
3-10
Purpose
Adjustment
Function (Purpose)
Used to adjust the finisher.
Section
Finisher
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch
1) Select an adjustment target item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
3) Press [OK] key. (The set value is saved.)
Finisher (100-sheet stapling)
*1: Not saved when the punch is not installed.
No,/Display item
Content
1
FNM101
Entry port transport motor
2
FNM104
Paper delivery transport motor
3
FNM108
Front alignment motor
4
FNM107
Stapler shift motor
5
FNM105
Load tray upper motor
6
FNM115
Staple motor
7
FNM110
Oscillation guide motor
8
FNM102
Buffer transport motor
9
FNM106
Load tray lower motor
10 FNM119
Roller nip motor
11 FNM114
YO motor
12 FNM120
Guide motor
13 FNM113
Rear edge falling motor
14 FNM117
Gripper belt motor
15 FNM116
Gripper arm motor
16 FNM121
Take-up transport motor
17 FNM112
Take-up swing motor
18 FNM118
Paper holding lever motor
19 FNM109
Rear alignment motor
20 FNCL102
Shutter clutch
21 FNM122
Paper delivery lower transport motor
22 FNSL101
Oscillation safety switch solenoid
23 FNFAN102
PWB cooling fan
24 FNFAN103
Upper tray cooling fan
25 FNFAN104
Lower tray cooling fan
26 PIM301
Transfer unit transport motor lock (*1)
No,/Display item
Content
1
FSM200
Entry port transport motor
2
FSM201
Transport motor
3
FSM212
Alignment roller (lead edge roller) motor
4
FSSL206
Inlet port path select solenoid
5
FSSL205
Lead edge stopper solenoid
6
FSSL203
Lead edge separation solenoid 1
7
FSSL204
Lead edge separation solenoid 2
8
FSM202
Alignment motor
9
FSM203
Lead edge stopper motor
10 FSM204
Roller guide motor
11 FSM210
Rear edge holding motor
12 FSM211
Rear edge shift motor
13 FSM213
Flapping motor
14 FSM214
Pull-in roller (separation) motor
15 FSM209
Staple motor
16 FSM206
Folding motor
17 FSM205
Push motor
No,/Display item
Content
1
FLSOL2
Folding/Straight branch solenoid
2
FLSOL3
Separation solenoid
3
FLSOL5
Internal 3-fold stopper solenoid
4
FLM11
Folding transport motor
5
FLM15
Folding position adjustment motor
6
FLM13
Exit port motor 2
7
FLM14
Exit port motor 1
8
FLM5
Inlet port motor
9
FLSOL4
Internal 3-fold tray branch solenoid
10 FLM8
Upper stopper motor
11 FLM9
Internal 3-fold stopper adjustment motor
12 FLM10
Lead edge holding guide motor
13 FLM7
Internal 3-fold tray (intermediate tray) motor
14 FLCL3
Folding position adjustment clutch (normal)
15 FLCL4
Folding position adjustment clutch (reverse)
No,/Display item
Content
1
FTM101
Trimmer transport motor
2
FTM103
Inlet port separation motor
3
FTM104
Paper delivery separation motor
4
FTM102
Registration motor
5
FTM106
Cutter motor
6
FTSL101
Registration solenoid
7
FTM105
Press motor
8
FTSL102
Paddle solenoid
Item/Display
Content
Setting
range
Default
value
A BUFFER
SHIFT1
Buffer paper shift amount
adjustment 1
50 - 150
100
B BUFFER
SHIFT2
Buffer paper shift amount
adjustment 2
50 - 150
100
C ALIGNMENT
Alignment width adjustment
50 - 150
100
D STAPLE
FRONT
(S-WIDTH)
Stapling position adjustment
(Front 1 position/Small width)
70 - 130
100
E STAPLE
FRONT
(W-WIDTH)
Stapling position adjustment
(Front 1 position/Wide width)
70 - 130
100
F STAPLE
REAR
(S-WIDTH)
Stapling position adjustment
(Rear 1 position/Small width)
70 - 130
100
G STAPLE
REAR
(W-WIDTH)
Stapling position adjustment
(Rear 1 position/Wide width)
70 - 130
100
H STAPLE
CENTER
Stapling position adjustment
(Center 2 positions)
85 - 115
100
I
PUNCH Y *
1
Punch hole position
adjustment
(Y: Main scanning direction)
85 - 115
100
J PUNCH X *
1
Punch hole position
adjustment
(X: Sub scanning direction)
50 - 150
100
K PUNCH
SKEW *
1
Punch mode skew
adjustment
98 - 102
100
L PUNCH
SKEW SHIN *
1
Punch mode skew
adjustment (thin paper)
99 - 103
100
No,/Display item
Content
Click on the first or last page to see other MX-6500N / MX-7500N (serv.man20) service manuals if exist.