Read Sharp MX-6240N / MX-7040N (serv.man26) Service Manual online
MX-7040N TROUBLESHOOTING 7 – 62
*1: In SIM22-41, the descriptions are abbreviated on the screen
because of the limitation on the number of characters (100K for
the paper feed counter).
the paper feed counter).
*2: In SIM22-41, the description of "(Delay of paper just before the
JAM from PS)" is omitted because of the limitation on the
number of characters.
number of characters.
MX-FN19/20
MX-RB15
MX-RB13
GBC punch
MX-FN21/22
MX-TM10
MX-FD10
APPD1_S
APPD1 remaining JAM
APPD2_N
APPD2 not-reached JAM
APPD2_S
APPD2 remaining JAM
LCC
A4/A3LCC paper feed JAM (LPFD1 not-reached JAM)
LPFD_SL
LPFD remaining JAM
(side A4/A3LCC paper feed paper)
(side A4/A3LCC paper feed paper)
MTR_ILG
Motor driver trouble JAM
PPD2_DRUM
PPD2 JAM (drum lock detection)
POD1_FUS
POD1 JAM (fusing winding detection)
PPD2_PRI
PPD2 JAM (Image preparation wait time-out)
CPFD2_DESK
CPFD2 JAM
(Desk communication abnormality detection)
(Desk communication abnormality detection)
PPD1_LCC
PPD1 JAM (LCC communication abnormality detection)
PPD2_FIN
PPD2 JAM
(Finisher communication abnormality detection)
(Finisher communication abnormality detection)
SIZE_ILG
Size illegal JAM
STOP_JAM
Emergency stop request JAM (Controller request)
NO_MATCH
Parameter inconsistency
JAM code
JAM content
FED_N
Finisher inlet port not-reached JAM
FED_S
Finisher inlet port remaining JAM
FFPD_N
Saddle section not-reached JAM
FFPD_S
Saddle section remaining JAM
FIN_TIME
Finisher paper early reaching JAM
FHS_N
Finisher paper exit not-reached JAM
FHS_S
Finisher paper exit remaining JAM
FSHS_N
Saddle transport not-reached JAM
FSHS_S
Saddle transport remaining JAM
FSFS_N
Saddle paper exit not-reached JAM
FSFS_S
Saddle paper exit remaining JAM
FSTPLJ
Finisher staple JAM
FPNCHJ
Finisher punch JAM
FSSTPLJ
Saddle staple JAM
PDPPD1_N
Finisher interface inlet port not-reached JAM
PDPPD1_S
Finisher interface inlet port remaining JAM
PDPPD2_N
Finisher interface outlet port not-reached JAM
PDPPD2_S
Finisher interface outlet port remaining JAM
FSSMJ
Finisher stapler shift motor JAM
FDRLMJ
Finisher paper exit roller lift motor JAM
FSDMJ
Finisher saddle motor JAM
FGMJ
Finisher gripper motor JAM
FSPTMJ
Finisher saddle paper transport motor JAM
FIN_PAOF
Finisher paper attribute data reception overflow
JAM code
JAM content
DCS100_N
Decurler unit transport pass sensor not-reached JAM
DCS100_S
Decurler unit transport pass sensor remaining JAM
DCTIME
Early reaching JAM
DCPAOF
Paper attribute data reception overflow
JAM code
JAM content
PIS150_N
Transport unit pass sensor not-reached JAM
PIS150_S
Transport unit pass sensor remaining JAM
JAM code
JAM content
GBCJ
GBC punch unit JAM
JAM code
JAM content
JAM code
JAM content
FNS101_N
Inlet port not-reached JAM (FN pass)
FNS101_S
Inlet port remaining JAM (FN pass)
FNS102_N
Paper exit not-reached JAM
FNS102_S
Paper exit remaining JAM
FNM110
Paper exit roller lift motor JAM
FNM117
Gripper motor JAM
FNM115
Staple JAM
FNM114
Discharged paper HOLD motor JAM
FNM113
Paper rear edge fall motor JAM
FNM116
Gripper arm motor JAM
FNM112
Paper alignment roller lift motor JAM
FNM118
Paper rear edge hold motor JAM
FCM102
Punch JAM
FNPAOF
Paper attribute data reception overflow
FNTIME
Early reaching JAM
FSS201_N
Saddle inlet port pass sensor delay JAM
FSS201_S
Saddle inlet port pass sensor remaining JAM
FSS203_N
Saddle vertical pass sensor delay JAM
FSS226_N
Saddle transport paper pass sensor 1 delay JAM
FSS226_S
Saddle transport paper pass sensor 1 remaining JAM
FSS227_N
Saddle paper exit pass sensor 2 delay JAM
FSS227_S
Saddle paper exit pass sensor 2 remaining JAM
FSM202
Saddle section saddle alignment motor JAM
FSM203
Saddle section lead edge stopper motor JAM
FSM204
Saddle section folding roller guide motor JAM
FSM210
Saddle section rear edge hold motor JAM
FSM211
Saddle section rear edge shift motor JAM
FSM213
Saddle section SADDLE flapping motor JAM
FSM214
Saddle section SEPARATION motor JAM
FSM206
Saddle section folding motor JAM
FSM205
Saddle section PUSH motor JAM
JAM code
JAM content
FTS103_N
Trimmer paper exit sensor delay JAM
FTS103_S
Trimmer paper exit sensor remaining JAM
FTS101_N
Trimmer inlet port sensor relay JAM
FTS101_S
Trimmer inlet port sensor remaining JAM
FTM103
Trimmer section inlet port separation motor JAM
FTM104
Trimmer section paper exit separation motor JAM
FTM102
Trimmer section registration motor JAM
FTM106
Trimmer section CUTTER motor JAM
FTM105
Trimmer section bundle press motor JAM
JAM code
JAM content
FLS30_N
Speed reduction timing sensor delay JAM
FLS30_S
Speed reduction timing sensor emaining JAM
FLS31_N
Separation timing sensor delay JAM
FLS31_S
Separation timing sensor emaining JAM
FLS32_N
Folding position adjustment sensor delay JAM
FLS32_S
Folding position adjustment sensor remaining JAM
FLS33_N
Upper stopper section paper detection sensor delay
JAM
JAM
FLS33_S
Upper stopper section paper detection sensor
remaining JAM
remaining JAM
FLS22_N
Outlet port 1 sensor delay JAM
FLS22_S
Outlet port 1 sensor remaining JAM
FLS27_N
Folding tray empty sensor delay JAM
FLS27_S
Folding tray empty sensor remaining JAM
FLS20_N
Inlet port sensor delay JAM
FLS20_S
Inlet port sensor remaining JAM
FLS21_N
Outlet port 2 sensor delay JAM
FLS21_S
Outlet port 2 sensor remaining JAM
FLM8
Folding section upper stopper motor JAM
FLM9
Folding SECTION 3-fold stopper motor JAM
FLM10
Folding section lead edge hold guide motor JAM
FLM7
Folding section folding tray paper exit motor JAM
FLENT_ERR
EntryStart time out JAM
FLEJT_ERR
EjectStartAck time out JAM
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man26) service manuals if exist.