Read Sharp MX-6240N / MX-7040N (serv.man25) Service Manual online
MX-7040N SIMULATION 6 – 10
2-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the loads
in the automatic document feeder and the
control circuit.
in the automatic document feeder and the
control circuit.
Section
DSPF
Operation/Procedure
1)
Select a target item of the operation check with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
2-6
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
fan motor.
fan motor.
Section
Scanner (reading)
Operation/Procedure
1)
Select a target item of the operation check with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
Descriptions of load operations
3
3-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
sors and the detectors in the finisher and
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The code names of the sensors and the detectors which are active
are highlighted.
are highlighted.
NOTE: When the punch module is installed, the code names are
displayed at the back of the sensor display.
Finisher (50-sheet stapling)
Finisher (100-sheet stapling)
Display
Content
SPUM
DSPF document feed motor
SPFM
DSPF transport motor
SPOM
DSPF document exit motor
SLUM
DSPF lift-up motor
SPFFAN
DSPF cooling fan motor
SPFC
DSPF document feed clutch
SRRC
DSPF No.2 registration roller clutch
STRRC
DSPF No.1 registration roller clutch
STRC
DSPF transport roller clutch
STMPS
Stamp solenoid
Display
Content
CLFM
LAMP cooling fan
No,/Display item
Content
1
PDPPD1
Finisher paper pass paper transport detector 1
2
PDPPD2
Finisher paper pass paper transport detector 2
3
PDOS
Finisher paper pass cover open/close sensor
4
FED
Finisher entry port paper detection
5
FAED1
Finisher tray 1 area detection 1
6
FAED2
Finisher tray 1 area detection 2
7
FAED3
Finisher tray 1 area detection 3
8
FFJHPD
Finisher alignment home position detection front
9
FRJHPD
Finisher alignment home position detection rear
10
FBED1
Finisher tray 1 paper detection
11
FBED2
Finisher tray 2 paper detection
12
FCCD
Finisher tray approach detection
13
FSLD1
Finisher tray 1 paper surface detection
14
FPDD1
Finisher discharged paper detection
15
FSLD2
Finisher tray 2 paper surface detection
16
FASHPD
Finisher rear edge assist home position detection
17
FSWHPD
Finisher oscillation guide home position detection
18
FSWOPD
Finisher oscillation guide open detection
19
FSTPD
Finisher staple tray paper detection
20
FSHPD
Finisher staple drive home position detection
21
FSTHPD
Finisher staple shift home position detection
22
FSD
Finisher staple empty detection
23
FSTD
Finisher staple lead edge position detection
24
FFANLK
Finisher fan motor lock detection
25
FSJOGD
Finisher stapler alignment interference detection
26
FSAD
Finisher staple safety SW
27
FSHTD
Finisher shutter open detection
28
FCD
Finisher connection detection
29
FFDD
Finisher front cover open detection
30
F24V
Finisher 24V output interruption detection
31
FPSW1
Finisher PUSHSW1 detection
32
FPSW2
Finisher PUSHSW2 detection
33
FPSW3
Finisher PUSHSW3 detection
34
FAED21
Finisher tray 2 area detection 1
35
FAED22
Finisher tray 2 area detection 2
36
FAED23
Finisher tray 2 area detection 3
No,/Display item
Content
1
FNS103
Staple tray paper sensor
2
FNS122
Finisher tray 1 area 1 sensor
3
FNS123
Finisher tray 1 area 2 sensor
4
FNS124
Finisher tray 1 area 3 sensor
5
FNS146
Discharge paper surface detection
6
FNS149
YO paper surface sensor
7
FNS118
Process tray paper surface sensor
8
FNS143
Lower tray paper surface sensor
9
FNS114
YOHP sensor
10
FNS112
Take-up switch home position sensor
11
FNS135
Paper holding lever home position sensor
12
FNS111
Roller nip home position sensor
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man25) service manuals if exist.