MX-6240N, MX-7040N (serv.man25). Section 6 Simulation - Updated November 2012 - Sharp Copying Equipment Service Manual (repair manual). Page 8

MX-7040N  SIMULATION  6 – 8

66

1

Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while 
checking with the LCD.

FAX

2

Used to enter a country code and set the default value for the country code.

FAX

3

Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the 
result.

FAX

4

Used to send the selected signals to the line and the main unit speaker. (Send level: max.) 

FAX

5

Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting) 
(For the kinds of send signals, refer to SIM66-04.)

FAX

6

Used to print the confidential registration check table (BOX NO., BOX name, passcode. (If there is no 
confidential registration, no print is made.)

FAX

7

Used to output all image data saved in the image memory. (Confidential data are also outputted.)

FAX

8

Used to send the selected sound messages to the line and the speaker. (Send level: Max.)

FAX

9

Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting) 
* For details of sound messages, refer to the sound message table of SIM66-08.

FAX

10

Used to clear the FAX and image send image data. (The confidential data are also cleared.)

FAX

11

Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.)

FAX

12

Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting) 
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.

FAX

13

Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.)

FAX

14

Used to execute the dial pulse (10PPS) send test and to adjust the make time.

FAX

15

Used to execute the dial pulse (20PPS) send test and to adjust the make time.

FAX

16

Used to execute the DTFM signal send test and to adjust the send level.

FAX

17

Used to send the DTMF signal to the line and the speaker. (Send level: Max.)

FAX

18

Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)

FAX

21

Used to print the selected items (system error, protocol monitor).

FAX

22

Used to set the handset sound volume. (This simulation can be executed even though the handset setting 
is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) 
(Japan model only)

FAX

24

Used to clear the FAST save data.

FAX

29

Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion 
table, the group expansion table, the program registration table, the interface memory box table, the meta 
data, InboundRouting, and the DocumentAdmin table).

FAX

30

Used to display the TEL/LIU status change, The display is highlighted by status change.

FAX

31

Used to set ON/OFF the port for output to TEL/LIU.

FAX

32

Used to check the fixed data received from the line and to display the result.

FAX

33

Used to execute detection of various signals with the line connected and to display the detection result. 
When a signal is detected, the display is highlighted.

FAX

34

Used to execute the send test and display the time required for sending image data in the test. Used to 
execute send test and display. (Unit: ms)

FAX

36

Used to check send and receive data from the MODEM controller to the MFP controller or the data line or 
the command line individually.

FAX

39

Used to check and change the destination setting saved in EEPROM of the FAX BOX.

FAX

42

Used to rewrite the program to power control installed in the FAX BOX.

FAX

43

Used to write the adjustment value into the power control installed in the FAX BOX.

FAX

61

Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while 
checking with the LCD.

FAX

62

Used to import the FAX receive data into a USB memory in PDF file type.

FAX

67

17

Printer reset

Printer

24

Printer color balance adjustment (Auto adjustment)

Printer

25

Printer color balance adjustment (Manual adjustment)

Printer

26

Used to set the target color balance of the printer mode auto color balance adjustment.

Printer

27

Used to set the service target of the printer mode auto color balance adjustment.

Printer

28

Used to set the default of the service target of the printer mode auto color balance adjustment.

Printer

31

Used to clear the printer calibration value.

Printer

33

Used to change the gamma of the printer screen.

Printer

34

Used to set the density correction in the printer high density section. 
(Support for the high density section tone gap)

Printer

36

Used to adjust the density in the low density section.

Printer

45

Used to adjust the printer image filter and trapping.

52

Used to set the default of the gamma of the printer screen.

Printer

54

Printer color balance adjustment (Automatic adjustment for each dither)

Printer