Read Sharp MX-6240N / MX-7040N (serv.man24) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 76
9-F
(4)
Automatic color balance adjustment by the
user (Printer color balance automatic
adjustment ENABLE setting and
adjustment) (Normally unnecessary to the
setting change)
Automatic color balance adjustment by the
user (Printer color balance automatic
adjustment ENABLE setting and
adjustment) (Normally unnecessary to the
setting change)
a. General
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the printer color balance and density).
ibration (auto adjustment of the printer color balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
tion with SIM 26-53.
CAUTION: This setting must be set to ENABLE only when the
user's understanding on the automatic adjustment of
the copy color balance and density and the user's oper-
ational ability are judged enough to execute the adjust-
ment.
the copy color balance and density and the user's oper-
ational ability are judged enough to execute the adjust-
ment.
When set to enable, operation procedures must be fully
explained to the user.
explained to the user.
b. Setting procedure
1)
Enter the SIM 26-53 mode.
2)
Select ENABLE or DISABLE with 10-key.
When disabling, set to "0" (NO). When enabling, set to "1"
(Yes).
(Yes).
3)
Press [OK] key.
When set to DISABLE, the menu of the user auto color calibration
(automatic adjustment of printer color balance and density) is not
displayed in the user program mode.
(automatic adjustment of printer color balance and density) is not
displayed in the user program mode.
(Auto color calibration by the user (Auto color balance adjust-
ment))
ment))
CAUTION: This adjustment is based on the service target color bal-
ance set with SIM 67-27 or SIM 67-28. If, therefore, the
above settings are not properly performed, this adjust-
ment cannot be made properly.
above settings are not properly performed, this adjust-
ment cannot be made properly.
1)
Enter the system setting mode.
2)
Enter the printer setting mode.
3)
Press the auto color calibration key.
4)
Press [EXECUTE] key.
The color patch image (adjustment pattern) is printed out.
5)
Set the color patch image (adjustment pattern) printed in pro-
cedure 4) on the document table.
cedure 4) on the document table.
Set the patch image so that the thin line is on the left side as
shown in the figure.
shown in the figure.
At that time, place 5 sheets of white paper on the above color
patch image (adjustment pattern).
patch image (adjustment pattern).
6)
Press [EXECUTE] key, and the printer color balance adjust-
ment is executed automatically.
ment is executed automatically.
The message, "Will you go on to the copy color balance
adjustment?" is displayed.
adjustment?" is displayed.
To execute the copy color balance adjustment successively,
perform the procedures same as the above.
perform the procedures same as the above.
ADJ 10
Manual paper feed tray paper
size (width) sensor adjustment
size (width) sensor adjustment
This adjustment must be performed in the following cases:
* The manual paper feed tray section has been disassembled.
* The manual paper feed tray unit has been replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&$/,%5$7,21
$˖
˷̚˹
˖&23<<(612
$˖
˖35,17(5<(612
%˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&$/,%5$7,21
$˖
˷̚˹
˖&23<<(612
$˖
˖35,17(5<(612
%˖
2.
Thin line
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man24) service manuals if exist.