Read Sony KV-AR29M50A Service Manual online
MODEL
COMMANDER DEST. CHASSIS NO.
CHASSIS
TRINITRON
®
COLOR TV
SERVICE MANUAL
BG3R
MODEL
COMMANDER DEST.
CHASSIS NO.
KV-AR29M50A
RM-952 Vietnam
SCC-U56J-A
RM-952
– 2 –
KV-AR29M50A
RM-952
Power requirements
110-240 V AC, 50/60 Hz
Power consumption (W)
Indicated on the rear of the TV
Television system
B/G, I, D/K, M
Color system
PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Channel coverage
B/G
VHF: E2 to E12 / UHF: E21 to E69
CATV: S01 to S03, S1 to S41
CATV: S01 to S03, S1 to S41
I
UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K
VHF: C1 to C12, R1 to R12
UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
M
VHF: A2 to A13 / UHF: A14 to A79
CATV: A-8 to A-2, A to W+4, W+6 to W+84
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘(Antenna)
75-ohm external terminal
Audio output (Speaker)
5W + 5W
Number of terminal
DVideo
Input: 3*
Output: 1
Phono jacks; 1 Vp-p, 75 ohms
* Two input lines available
≥ Audio
Input: 3*
Output: 1
Phono jacks; 500 mVrms
* Two input lines available
(S Video)
Input : 1
Y: 1 Vp-p, 75 ohms,
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
(Component
Input : 1
Phono jacks:
Video)
Y: 1 Vp-p, 75 ohms,
sync negative
C
sync negative
C
B
: 0.7 Vp-p, 75 ohms
C
R
: 0.7 Vp-p, 75 ohms
Audio: 500mVrms
2 (Headphone)
Output: 1
Stereo minijack
Picture tube
29 in.
Tube size (cm)
72
Measured diagonally
Screen size (cm)
68
Measured diagonally
Dimension (w/h/d,mm)
765
× 578 × 502
Mass (kg)
49
Design and specifications are subject to change without notice.
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Note
– 3 –
KV-AR29M50A
RM-952
TABLE OF CONTENTS
SELF DIAGNOSTIC FUNCTION ........................................ 4
1. DISASSEMBLY
1-1.
Rear Cover Removal ................................................... 7
1-2.
Speaker Removal ........................................................ 7
1-3.
Chassis Assy Removal ................................................ 7
1-4.
Service Position .......................................................... 7
1-5.
Terminal Bracket and J Board Removal .................... 7
1-6.
D3 Board Removal ..................................................... 7
1-7.
H1 and H2 Boards Removal ....................................... 8
1-8.
A and B9 Boards Removal ......................................... 8
1-9.
Picture Tube Removal ................................................. 8
2. SET-UP ADJUSTMENTS
2-1.
Beam Landing ........................................................... 10
2-2.
Convergence .............................................................. 11
2-3.
Focus Adjustment ..................................................... 13
2-4.
G2 (SCREEN) and White Balance Adjustment ....... 14
3. CIRCUIT ADJUSTMENTS
3-1.
Adjustment With Commander .................................. 15
3-2.
Adjustment Method .................................................. 15
3-3.
Picture Quality Adjustments ..................................... 20
3-4.
Deflection Adjustments ............................................ 20
3-5.
H-Trapezoid Adjustment .......................................... 21
3-6.
A Board Adjustment After IC003 (MEMORY)
Replacement .............................................................. 21
Replacement .............................................................. 21
3-7.
Picture Distortion Adjustment .................................. 22
Section
Title
Page
Section
Title
Page
4. DIAGRAMS
4-1.
Block Diagram .......................................................... 23
4-2.
Circuit Board Location ............................................. 25
4-3.
Schematic Diagram ................................................... 26
(1) A Board Schematic Diagram .............................. 27
(2) B9 Board Schematic Diagram ............................ 31
(3) C6 Board Schematic Diagram ............................ 33
(4) H1 Board Schematic Diagram ............................ 35
(5) J Board Schematic Diagram ............................... 37
(6) H2 Board Schematic Diagram ............................ 38
(7) D3 Board Schematic Diagram ............................ 39
(8) VM1 Board Schematic Diagram ........................ 40
(1) A Board Schematic Diagram .............................. 27
(2) B9 Board Schematic Diagram ............................ 31
(3) C6 Board Schematic Diagram ............................ 33
(4) H1 Board Schematic Diagram ............................ 35
(5) J Board Schematic Diagram ............................... 37
(6) H2 Board Schematic Diagram ............................ 38
(7) D3 Board Schematic Diagram ............................ 39
(8) VM1 Board Schematic Diagram ........................ 40
4-4.
Voltage List and Waveforms ..................................... 41
4-5.
Printed Wiring Boards and Parts Location ............... 45
4-6.
Semiconductors ......................................................... 51
5. EXPLODED VIEWS
5-1.
Speaker Bracket ........................................................ 53
5-2.
Chassis ...................................................................... 54
5-3.
Picture Tube .............................................................. 55
6. ELECTRICAL PARTS LIST ......................................... 56
INSTRUCTION MANUAL
– 4 –
KV-AR29M50A
RM-952
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER indicator will
automatically begin to flash. A description of the self diagnostic function is explained in the instruction manual.
The number of times the STANDBY/TIMER indicator flashes translates to a probable source of the problem. If an error
symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in
memory to reveal past problems and how often these problems occur.
automatically begin to flash. A description of the self diagnostic function is explained in the instruction manual.
The number of times the STANDBY/TIMER indicator flashes translates to a probable source of the problem. If an error
symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in
memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an errors occurs, the STANDBY/TIMER indicator will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the indicator will identify the first of the problem areas.
problem. If there is more than one error, the indicator will identify the first of the problem areas.
Result for all of the following diagnosis items are displayed on screen. No error has occured if the screen displays a “0”.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 2-4 of this manual.
* R(Q703), G(Q702) or B(Q701) out is faulty (C6 board).
SELF DIAGNOSTIC FUNCTION
Diagnostic
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP) or
overvoltage
(OVP)
overvoltage
(OVP)
• Vertical deflection
stopped
• Horizontal
deflection
overdrive
overdrive
• White balance
failure (no
PICTURE)
PICTURE)
• Micro reset
Detected
Symptoms
• Power does not come on.
• No power is supplied to the
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is stopped.
• No raster is generated.
• CRT cathode current
• CRT cathode current
detection reference pulse
output is small.
output is small.
• Power is shut down shortly,
after this return back to
normal.
normal.
• Detect Micro latch up.
No. of times
STANDBY/TIMER
indicator flashes
Does not light
2 times
5 times
—
Self-diagnostic
display/Diagnostic
result
—
002:000 or
002:001~255
003:001~255
004:001~255
003:001~255
004:001~255
at the same time
005:000 or
005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out F4601
(F)
• H.OUT Q511 is shorted.
(A board)
• Q701, Q702, Q703 is
shorted (C6 board)
• -13V is not supplied.
(A board)
• IC 503 faulty (A board)
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• R(Q703), G(Q702) or
• R(Q703), G(Q702) or
B(Q701) out is faulty
(C6 board)
(C6 board)
• IC301 is faulty. (A board)
• No connection A board to
• No connection A board to
C6 board.
• Discharge CRT (C6 Board)
• Static discharge
• External noise
• Static discharge
• External noise