Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man47) Service Manual online
MX-7000N SELF DIAG AND TROUBLE CODE 8 – 21
F2-78
Registration exclusive image density
sensor trouble (Transfer belt surface
reflection ratio abnormality)
sensor trouble (Transfer belt surface
reflection ratio abnormality)
F2-80
Half tone process control 1st patch
reference value trouble (K)
reference value trouble (K)
F2-81
Half tone process control 1st patch
reference value trouble (C)
reference value trouble (C)
F2-82
Half tone process control 1st patch
reference value trouble (M)
reference value trouble (M)
F2-83
Half tone process control 1st patch
reference value trouble (Y)
reference value trouble (Y)
F2-84
Half tone process control 2nd patch
reference value trouble (K)
reference value trouble (K)
Trouble content
The transfer belt surface is scanned by the image
density sensor before starting the registration, and
adjust the sensor gain so that the output is kept at
a certain level. However, the output is not within
the specified range though the senor gain is
adjusted.
density sensor before starting the registration, and
adjust the sensor gain so that the output is kept at
a certain level. However, the output is not within
the specified range though the senor gain is
adjusted.
Section
PCU
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble, calibration plate solenoid
operation trouble
trouble between PCU PWB and the image density
sensor, image density sensor dirt, transfer belt
cleaning trouble, calibration plate solenoid
operation trouble
Check and
remedy
remedy
Check the sensor and the harness. Check the
calibration plate solenoid operation and the
transfer belt surface state.
If the trouble is not cleared, replace the image
sensor exclusively used for registration, replace
the transfer belt, replace the calibration plate
solenoid, or replace the PCU PWB according to
the check result.
calibration plate solenoid operation and the
transfer belt surface state.
If the trouble is not cleared, replace the image
sensor exclusively used for registration, replace
the transfer belt, replace the calibration plate
solenoid, or replace the PCU PWB according to
the check result.
Trouble content
The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in BK.
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in BK.
Section
MFP
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
Check and
remedy
remedy
Use SIM44-2 to execute the process control
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
Trouble content
The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in C.
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in C.
Section
MFP
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
Check and
remedy
remedy
Use SIM44-2 to execute the process control
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
Trouble content
The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in M.
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in M.
Section
MFP
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
Check and
remedy
remedy
Use SIM44-2 to execute the process control
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
Trouble content
The low-density rising point or the high-density
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in Y.
saturation point cannot be calculated because of a
calculation error in the primary approximation
formula of the sensor output ratio for the LSU
PWM value obtained from the first step patch print
result when executing the half tone process control
in Y.
Section
MFP
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
Check and
remedy
remedy
Use SIM44-2 to execute the process control
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
Trouble content
The low-density section output is greater than the
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula
(formula of the sensor output ratio for the LSU
PWM value) from the second step patch print
result when executing the half tone process control
in BK.
middle-density section output when connecting the
low-density section approximation formula and the
middle-density section approximation formula
(formula of the sensor output ratio for the LSU
PWM value) from the second step patch print
result when executing the half tone process control
in BK.
Section
MFP
Case 1
Cause
Image density sensor trouble, harness connection
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
trouble between PCU sub PWB and the image
density sensor, image density sensor dirt, transfer
belt cleaning trouble
Check and
remedy
remedy
Use SIM44-2 to execute the process control
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
sensor gain adjustment. If "ERROR" is displayed,
check the sensor and the harness. If the
adjustment is completed, check the drum surface
state and the belt surface state.
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man47) service manuals if exist.