Read Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man5) Service Manual online
MX-6070V SIMULATION 6 – 5
24
35
Used to clear the toner cartridge use status
data
data
25
1
Used to check the operations of the
developing section
developing section
2
Used to make the initial setting of toner
density when replacing developer
density when replacing developer
2-2
-5
2
4
Used to display the operation data of the
toner supply quantity
toner supply quantity
5
Used to display the toner density correction
data
data
10
Developer/drum serial no setting
26
1
Used to set Yes/No of installation of the
right paper exit tray
right paper exit tray
2-1
2
Used to set the paper size of the large
capacity tray (LCC)
capacity tray (LCC)
2-1
3
Used to set the specifications of the auditor
2-1
5
Used to set the count mode of the total
counter and the maintenance counter
counter and the maintenance counter
2-2
6
Used to set the specifications of the
destination
destination
7
Used to set the machine ID
8
Used to set the counter mode (long scale)
2-2
10
Used to set the trial mode of the network
scanner
scanner
18
Used to set Disable/Enable of the toner
save mode operation
save mode operation
2-4
30
Used to set the operation mode
corresponding to the CE mark
corresponding to the CE mark
32
Used to set the specifications of the fusing
cleaning operation
cleaning operation
35
Used to set the display/mode of Sim 22-4
trouble history when a same trouble
occurred repeatedly. There are two display
modes. Display as one trouble and display
as several series of troubles
trouble history when a same trouble
occurred repeatedly. There are two display
modes. Display as one trouble and display
as several series of troubles
38
Used to set continue/stop of print when the
maintenance life is reached
maintenance life is reached
41
Used to set Enable/Disable of the
magnification ratio automatic select function
in the center binding mode
magnification ratio automatic select function
in the center binding mode
49
Used to set the print speed of postcard
mode
mode
50
Used to set functions
2-1
52
Used to set whether non-printed paper is
counted up or not
counted up or not
2-2
65
Used to set the finisher alarm mode
2-1
66
Simulation password setting
69
Used to set the operating conditions for
toner near end
toner near end
2-4
73
Enlargement continuous shoot, A3 wide
copy mode image loss adjustment
copy mode image loss adjustment
74
Used to set the OSA trial mode
78
Used to set the password of the remote
operation panel
operation panel
2-1
79
Used to set Yes/No of the pop-up display of
security
security
85
Simulation function setting
27
2
Used to set the sender's registration
number and the HOST server telephone
number
number and the HOST server telephone
number
2-5
4
Used to set the initial call and toner order
auto send
auto send
2-5
5
Used to set the machine tag No.
6
Used to set of the manual service call
7
Used to set of the enable, alert callout
2-5
9
Used to set the paper transport time
recording Yes/No threshold value and
shading gain adjustment retry number
recording Yes/No threshold value and
shading gain adjustment retry number
2-5
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
27
10
Used to clear the trouble prediction history
information
information
11
Used to check the serial communication
retry number and the scanner gain
adjustment retry number history
retry number and the scanner gain
adjustment retry number history
12
Used to check the high density, halftone
process control and the automatic
registration adjustment error history
process control and the automatic
registration adjustment error history
13
Used to check the history of paper transport
time between sensors
time between sensors
14
Used to set the FSS function connection
test mode
test mode
2-5
15
Used to display the FSS connection status
2-5
16
Used to set the FSS alert send
2-5
17
Used to set the FSS paper order alert
2-5
30
1
Used to check the operations of the sensors
and the detectors in other than the paper
feed section and the control circuit
and the detectors in other than the paper
feed section and the control circuit
2
Used to check the operations of the sensors
and the detectors in the paper feed section
and the control circuit
and the detectors in the paper feed section
and the control circuit
30
Used to check the operation of the motion
sensor
sensor
40
2
Manual paper feed tray paper width sensor
adjustment
adjustment
4
7
Used to set the adjustment value of the
manual paper feed tray paper width sensor
manual paper feed tray paper width sensor
41
1
Used to check the operations of the
document size sensor and the control
circuit
document size sensor and the control
circuit
3
2
Used to adjust the document size sensor
detection level
detection level
3
3
Used to check the operations of the
document size sensor and the control
circuit
document size sensor and the control
circuit
43
1
Used to set the fusing temperature in each
mode
mode
2
Used to set the fusing operation and
preheating
preheating
20
Used to set the environment correction
under low temperature and low humidity (L/
L) for the fusing temperature setting
(Sim43-2) in each paper mode
under low temperature and low humidity (L/
L) for the fusing temperature setting
(Sim43-2) in each paper mode
21
Used to set the environment correction
under high temperature and high humidity
(H/H) for the fusing temperature setting
(Sim43-2) in each paper mode
under high temperature and high humidity
(H/H) for the fusing temperature setting
(Sim43-2) in each paper mode
24
Fuser motion setup
35
Fusing nip operation check
44
1
Used to set each correction operation
function in the image forming section
function in the image forming section
2
Used to adjust the sensitivity of the image
density sensor
density sensor
2-2
-3
2
4
Used to set the conditions of the high
density process control operation
density process control operation
6
Used to execute the high density process
control forcibly
control forcibly
1-5
2-3
9
Used to display the result data of the high
density process control operation
density process control operation
12
Used to display the operation data of the
high density process control and the image
density sensor
high density process control and the image
density sensor
14
Used to display the output level of the
temperature and humidity sensor
temperature and humidity sensor
15
Used to set the OPC drum idle rotation
17
Process refresh execution
21
Used to set the halftone process control
target
target
5
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man5) service manuals if exist.