MX-4100N, MX-4101N, MX-5000N, MX-5001N (serv.man14). Service Manual-Section 6-Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 12

MX-4101N  SIMULATION  6 – 12

NOTE: "A: SADDLE POSITION (Saddle binding position adjust-

ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting 

±5.0mm)

In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.

 

 

4-2

Operation test/check

Function (Purpose) Used to check the operations of the sen-

sors and detectors in the desk/large capac-
ity tray, and the control circuit of those.

Desk/Large capacity tray (LCC)

Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.

 

4-3

Operation test/check

Function (Purpose) Used to check the operations of the loads

in the desk/large capacity tray (LCC), and
the control circuit of those.

Desk/Large capacity tray (LCC)

Operation/Procedure
1)

Select the load item that is required to operation check with the
touch panel key.

2)

Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.

DCSI1

Desk 1 installation detection

DPFD1

Desk 1 transport detection

DLUD1

Desk 1 upper limit detection

DPED1

Desk 1 paper empty detection

DCSPD1

Desk 1 remaining paper quantity detection

DCSS11

Desk 1 rear edge detection 1

DCSS12

Desk 1 rear edge detection 2

DCSS13

Desk 1 rear edge detection 3

DCSS14

Desk 1 rear edge detection 4

DCSI2

Desk 2 installation detection

DPFD2

Desk 2 transport detection

DLUD2

Desk 2 upper limit detection

DPED2

Desk 2 paper empty detection

DCSPD2

Desk 2 remaining paper quantity detection

DCSS21

Desk 2 rear edge detection 1

DCSS22

Desk 2 rear edge detection 2

DCSS23

Desk 2 rear edge detection 3

DCSS24

Desk 2 rear edge detection 4

DSW_DSK

Desk transport cover open/close detection

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

),1,6+(5$'-8670(17

$˖

˷̚˹

˖6$''/(326,7,21

$˖

˖)2/',1*326,7,21

%˖

˖)5217$'-867

&˖

˖5($5$'-867

'˖

˖67$3/(5($55

)˖

˖67$3/(5($5

(˖

˖67$3/()5217

*˖

˖67$3/()52175

+˖

˖67$3/(%27+

,˖

˖67$3/(3,7&+

-˖

˖381&+&(17(5

.˖

˖381&++2/(

/˖

2.

LPFD

LCC transport sensor

LUD

LCC tray upper limit sensor

LDD

LCC tray lower limit sensor

LPED

LCC tray paper empty sensor

LCD

LCC tray insertion detection

LDSW

LCC upper open/close detection SW

LRE

LCC lift motor encoder sensor

L24VM

LCC24V power monitor

LLSW

LCC upper limit SW

LTOD

LCC main unit connection detection

DPFM

Desk main motor

DLUM1

Desk 1 lift-up motor

DPUC1

Desk 1 paper feed clutch

DLUM2

Desk 2 lift-up motor

DPUC2

Desk 2 paper feed clutch

DTRC

Desk transport clutch

LPFM

LCC transport motor

LLM

LCC lift motor

LPFC

LCC paper feed clutch

LPFS

LCC paper feed solenoid

LTRC

LCC transport clutch

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

'6./&&6(1625&+(&.

'&6,

'3)'

'/8'

'3('

'&63'

'&66

'&66

'&66

'&66

'&6,

'3)'

'/8'

'3('

'&63'

'&66

'&66

'&66

'&66

'6:B'6.

㩷

㩷

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

'6./&&/2$'&+(&.

(;(&87(

'3)0

'/80

'/80

'38&

'38&

'75&