MX-3050N, MX-3060N, MX-3070N, MX-3550N, MX-3560N, MX-3570N, MX-4050N, MX-4060N, MX-4070N (serv.man2). Phoenix Handy Guide MX-XX60 MX-XX70 Updated Dec 16 Note Handy Guides are not a Substitute for the Service Manual - Sharp Copying Equipment Handy Guide. Page 60

 

 

01  Shading correction data display 
02  Shading correction execution (force) 
03  CCD gamma & colour correction adjustment 
04  Scanner test chart patch density list display 
05  CCD colour balance & gamma default setting 
07  Register the standard target of copy mode 

auto colour balance adjustment (Service) 

08  Set the standard copy mode auto colour 

balance target to factory default (Service) 

11  Set the standard target colour balance 

adjustment (Factory) 

 

01  Test print (Colour mode) 
02  Test print (B/W mode) 
04  Printer self-print test 
05  Printer self-print test (PCL) 
06  Printer self-print test (PS) 

 

01  LCD touch panel adjustment 
02  LCD touch panel adjustment result display 
05  Operation panel key input test 

 

01  Fax Soft SW setting 

SW24 

Communication Signal sending level 
(bits 1-8) 

SW27-4 

V.34 mode function (call arrival): 
0 = V.34 valid, 1 = V.34 invalid. 

SW27-5 

V.34 mode function (polling when 
calling): 
0 = V.34 valid, 1 = V.34 invalid. 

SW27-6 

V.34 mode function (manual 
communication): 
0 = V.34 valid. 1 = V.34 invalid. 

SW33-6, 
SW33-7; 

Transmission cable amplitude 
equaliser:- 
00 = 0dB, 01 = 4dB 
10 = 8dB, 11 = 12dB 

02  Country code default set (Fax) 
03  Fax PWB (modem) controller memory check 
04  Fax signal line check (Max level) 
05  Fax signal line check (Soft SW setting level) 
06  Fax list print (confidential registration) 
07  Fax image memory printout (all data) 
08  Fax sound message setup 

 
 

09  Fax signal line check (Soft SW setting) 
10  Fax & Image data all memory clear 
11  Voice signal check (line/speaker 300bps) 
12  Voice signal check (line/speaker 300bps) 
13  Register dial number for Sim 66-14/15/16 
14  Adjust/check the time dial pulse (10bps) 
15  Adjust/check the time dial pulse (20bps) 
16  Adjust/check the send level DTFM signal 
17  DTFM signal to send to line (Max level) 
18  DTFM signal to send to line (Soft SW level) 
21  Print various registration information 
22  Set the sound volume of the handset (Japan) 
29  Fax address book clear 
30  Tel/LIU sensor status check 
31  ON/OFF setting of output port (Tel/LIU) 
32  Received data check (comparison) 
33  Busy Tone/CNG/CED/FNET detect check 
36  Check Send/Receive from modem. 
39  Check Destination saved in Fax EEPROM 
42  Rewrite PIC program installed on Fax box 
43  Write program & adjustment values to PIC 

installed on Fax 

61  Display FAX related soft switch (151-250) 
62  FAX receive data export in PDF format. 

 

17  Printer NVRAM clear 
24  Printer colour balance auto adjustment 
25  Printer colour balance manual adjustment  
26  Set the target colour balance for printer 

mode auto colour adjustment 

27  Set the target colour balance for printer 

mode auto colour adjustment (Service) 

28  Set the printer mode auto colour adjustment 

back to factory default (Service) 

31  Printer calibration data clear 
33  Printer screen gamma adjust. (PCL/PS) 
34  Printer maximum density adjustment mode 
36  Adjust the density in printer low density 

areas 

41  2 colour print setup 
42  2 colour print density setup 
43  2 colour mode colour balance adjustment for 

printer 

52  Printer default gamma check (PCL/PS) 
54  Printer colour balance adjustment