Read Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man2) Handy Guide online
TEST SIMULATION
SHARP
58
46
Copy/Scanner Image Density Adjustment
47 JPEG compression rate setting
48 Function setting for copy output
51 Heavy paper mode gamma adjustment
52 Heavy paper mode gamma default set
54 Engine half tone density adjustment (dither).
55 Drop out colour mode adjustment for Image
48 Function setting for copy output
51 Heavy paper mode gamma adjustment
52 Heavy paper mode gamma default set
54 Engine half tone density adjustment (dither).
55 Drop out colour mode adjustment for Image
Send mode.
58 Copy mode pseudo resolution setting
(smoothing process).
60 Sharpness adjustment (colour auto mode)
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
65 Colour correction table setting.
66 Watermark reproduction adjustment for
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
65 Colour correction table setting.
66 Watermark reproduction adjustment for
Copy/Printer
68 Auto resolution setting
74 Copy half tone balance adjustment
90 Set process operation of high compression
74 Copy half tone balance adjustment
90 Set process operation of high compression
PDF images
91 Black text reproduction adjustment
48
Magnification & Motor Adjustment
01 Scan image magnification adjust (Main scan)
05 Scan image magnification adjust (Sub scan)
06 Motor rotation speed adjustment
05 Scan image magnification adjust (Sub scan)
06 Motor rotation speed adjustment
49
ROM Version Upgrade
01 Firmware Upgrade Program
03 E Manual (Op manual) Update Program
05 Watermark Update Program
06 OCR Dictionary Update Program
10 ACU Firmware Update Program
03 E Manual (Op manual) Update Program
05 Watermark Update Program
06 OCR Dictionary Update Program
10 ACU Firmware Update Program
50
Image Position Adjustment
01 Lead edge/copy position & image loss
adjustment
05 Printer lead edge adjustment (sub scan)
06 SPF Lead edge/copy position adjustment
10 Print off-centre deviation adjustment.
12 Original centre deviation adjustment.
20 Manual colour registration adjustment.
22 Auto colour registration & drum adjustment.
23 Registration for temperature adjustment
06 SPF Lead edge/copy position adjustment
10 Print off-centre deviation adjustment.
12 Original centre deviation adjustment.
20 Manual colour registration adjustment.
22 Auto colour registration & drum adjustment.
23 Registration for temperature adjustment
setup
24 Auto registration & drum data display
27 Image loss adjustment (Fax/Scanner)
27 Image loss adjustment (Fax/Scanner)
50
Image Position Adjustment
28 Service automatic adjustment (OC/SPF
position & BK magnification etc)
51
Resist Roller Adjustment
01 Secondary transfer voltage ON timing
adjustment
02 Resist roller adjustment
53
Document Feeder Adjustment
06 SPF document tray size adjustment
07 SPF document tray size adjust value set.
08 SPF scanning position adjustment
09 SPF dirt detection setting
10 SPF dirt detection execution
07 SPF document tray size adjust value set.
08 SPF scanning position adjustment
09 SPF dirt detection setting
10 SPF dirt detection execution
55
MFP Data Setting
01 Engine soft switch setting
SW12-4
Enable 1
st
Transfer Belt lubrication
(applies yellow toner at specific
page count) – [50/60ppm only]:-
0 = Enabled, 1 = Disabled
page count) – [50/60ppm only]:-
0 = Enabled, 1 = Disabled
SW24-7
L4-11 detection disable (used for
troubleshooting when Finisher or
Centre Tray Unit is not installed).
0 = Enabled, 1 = Disabled
troubleshooting when Finisher or
Centre Tray Unit is not installed).
0 = Enabled, 1 = Disabled
SW27-4
Enable 1
st
Transfer Belt lubrication
at installation & maintenance when
TC1 Belt Counter Sim24-4 is cleared
[50/60ppm only]:-
0 = Enabled, 1 = Disabled
TC1 Belt Counter Sim24-4 is cleared
[50/60ppm only]:-
0 = Enabled, 1 = Disabled
02 Scanner soft switch setting
03 Controller soft switch setting
03 Controller soft switch setting
SW4-7
Custom Paper Size entry for Tray 1
0 = Disabled, 1 = Enabled
SW6-2
Ethernet Link Speed:-
0 = 100Base TX, 1 = 10Base T
SW6-3
Ethernet Duplex Mode:-
0 = Full, 1 = Half
SW6-4
Ethernet 100/1000 Link Speed:-
0 = 100Base TX, 1 = 1000Base T
SW9-5
Maintenance notification setting by
Printer MIB:-
Printer MIB:-
0 = Enabled, 1 = Disabled
SW17-3
A3 / Postcard Counter Mode
0 = Disabled, 1 = Enabled
SW18-6
Hide Device Counter Clear
(SIM24-6 to 24-15)
(SIM24-6 to 24-15)
0 = Hide [Default], 1 = Display
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man2) service manuals if exist.