Read Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man5) Service Manual online
DX-C401 SIMULATION 5 – 14
• 4.3 Inch LCD model
• 8.5 Inch LCD model
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an adjustment target item with [
] [] key.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (For the 4.3 Inch LCD model, press the OSA
shortcut key.) (The set value is saved.)
shortcut key.) (The set value is saved.)
• 4.3 Inch LCD model
• 8.5 Inch LCD model
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the paper feed tray,
and the control circuit of those.
and the control circuit of those.
Section
Paper feed tray (Option)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
Item/Display
Content
Setting
range
Default
value
A
FPAM ADJUST
Paper alignment width
adjustment *1
adjustment *1
40 - 60
50
B
FDRLM ADJUST
Paper delivery roller
descending position
adjustment
descending position
adjustment
40 - 60
50
Item A:
When the adjustment value is increased by 1, the alignment plate
F/R width is narrowed by 0.419mm in alignment operation.
When the adjustment value is decreased by 1, the alignment plate
F/R width is widened by 0.419mm in alignment operation.
The alignment plate F and the alignment plate R cannot be
adjusted separately. The shift amount on the F side and that on
the R side are alternatively corrected everytime the adjustment
value is increased by 1. (Correction with 51 for the F side, and 52
for the R side. ... 59 for the F aide, and 60 for the R side. Similar
when the set value is decreased.)
F/R width is narrowed by 0.419mm in alignment operation.
When the adjustment value is decreased by 1, the alignment plate
F/R width is widened by 0.419mm in alignment operation.
The alignment plate F and the alignment plate R cannot be
adjusted separately. The shift amount on the F side and that on
the R side are alternatively corrected everytime the adjustment
value is increased by 1. (Correction with 51 for the F side, and 52
for the R side. ... 59 for the F aide, and 60 for the R side. Similar
when the set value is decreased.)
Item B:
When the adjustment value is increased by 1, the shift amount of
the paper delivery roller is changed by 0.11mm toward the
pressure increasing side (*1).
When the adjustment value is decreased by 1, the shit amount of
the paper delivery roller is changed by 0.11mm toward the
pressure decreasing side (*1).
*1:
the paper delivery roller is changed by 0.11mm toward the
pressure increasing side (*1).
When the adjustment value is decreased by 1, the shit amount of
the paper delivery roller is changed by 0.11mm toward the
pressure decreasing side (*1).
*1:
The pressure increasing side means the direction to
increase the paper delivery roller pressure onto paper, and
the pressure decrease side means the direction to decrease
the paper delivery roller pressure onto paper.
increase the paper delivery roller pressure onto paper, and
the pressure decrease side means the direction to decrease
the paper delivery roller pressure onto paper.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
),1/2$'&+(&.
7(67
)3*6
)370
)60
)36
)3$0)
)6&)
)3'0
)'5/0
)7/0
)$5/6
)3$05
)%&)
(;(&87(
D1PPD
Paper feed tray 2 paper transport detector
D1ULD
Paper feed tray 2 upper limit detector
D1PED
Paper feed tray 2 paper empty detector
D1PQD
Paper feed tray 2 paper remaining quantity detector
D1PRED1
Paper feed tray 2 paper rear edge detector 1
D1PRED2
Paper feed tray 2 paper rear edge detector 2
D1PRED3
Paper feed tray 2 paper rear edge detector 3
D1COCS
Paper feed tray 2 cover open/close sensor
D2MDC
Paper feed tray 3 installation detection connector
D2PPD
Paper feed tray 3 paper transport detector
D2ULD
Paper feed tray 3 upper limit detector
D2PED
Paper feed tray 3 paper empty detector
D2PQD
Paper feed tray 3 paper remaining quantity detector
D2PRED1
Paper feed tray 3 paper rear edge detector 1
D2PRED2
Paper feed tray 3 paper rear edge detector 2
D2PRED3
Paper feed tray 3 paper rear edge detector 3
D2COCS
Paper feed tray 3 cover open/close sensor
D3MDC
Paper feed tray 4 installation detection connector
D3PPD
Paper feed tray 4 paper transport detector
D3ULD
Paper feed tray 4 upper limit detector
D3PED
Paper feed tray 4 paper empty detector
D3PQD
Paper feed tray 4 paper remaining quantity detector
D3PRED1
Paper feed tray 4 paper rear edge detector 1
D3PRED2
Paper feed tray 4 paper rear edge detector 2
D3PRED3
Paper feed tray 4 paper rear edge detector 3
D3COCS
Paper feed tray 4 cover open/close sensor
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
),1,6+(5$'-8670(17
˖)3$0$'-867
$˖
˖)'5/0$'-867
%˖
7(67
Click on the first or last page to see other DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man5) service manuals if exist.