Read Sharp AR-M700 (serv.man28) Service Manual online
AR-M550/M620/M700 SELF DIAG MESSAGE AND TROUBLESHOOTING 9 - 21
Main
code
code
Sub
code
Title
Finisher/saddle sensor connector
connection trouble
connection trouble
F1
51
Phenomenon
Display
Lamp
Message
Message
Details
Finisher/saddle sensor
connector connection
trouble
The connector
connection detection
input of the guide HP
sensor is off.
The connector
connection detection
input of the push lead
edge sensor is off.
connector connection
trouble
The connector
connection detection
input of the guide HP
sensor is off.
The connector
connection detection
input of the push lead
edge sensor is off.
Section
Finisher
Operation
mode
mode
Note
Case 1
Trouble
position/
Cause
position/
Cause
Finisher control PWB
trouble
Malfunction caused by
noises
trouble
Malfunction caused by
noises
Remedy
Replace the finisher
control PWB.
control PWB.
Note
Main
code
code
Sub
code
Title
Finisher/micro switch trouble
F1
52
Phenomenon
Display
Lamp
Message
Details
Finisher/micro switch
trouble
With all cover PI (photo
sensor) ON, the transport
cover MS is off fort 1sec
continuously from starting
copying.
With all cover PI (photo
sensor) ON, the front
cover MS is off fort 1sec
continuously from starting
copying.
With all cover PI (photo
sensor) ON, the paper
exit cover MS is off fort
1sec continuously from
starting copying.
trouble
With all cover PI (photo
sensor) ON, the transport
cover MS is off fort 1sec
continuously from starting
copying.
With all cover PI (photo
sensor) ON, the front
cover MS is off fort 1sec
continuously from starting
copying.
With all cover PI (photo
sensor) ON, the paper
exit cover MS is off fort
1sec continuously from
starting copying.
Section
Finisher
Operation
mode
mode
Note
Case 1
Trouble
position/
Cause
position/
Cause
Finisher control PWB
trouble
Malfunction caused by
noises
trouble
Malfunction caused by
noises
Remedy
Replace the finisher
control PWB.
control PWB.
Note
Main
code
code
Sub
code
Title
Finisher-inserter communication
trouble
trouble
F1
60
Phenomenon
Display
Lamp
Message
Message
Details
Finisher/inserter
communication trouble
communication trouble
Section
Inserter
Operation
mode
mode
Note
Case 1
Trouble
position/
Cause
position/
Cause
Improper connection or
disconnection of the
connector and the
harness between the
finisher and the inserter
unit
disconnection of the
connector and the
harness between the
finisher and the inserter
unit
Remedy
Check the connector and
the harness in the
communication line.
the harness in the
communication line.
Note
Case 2
Trouble
position/
Cause
position/
Cause
Finisher control PWB
trouble
Control PWB (PCU)
trouble
trouble
Control PWB (PCU)
trouble
Remedy
Replace the finisher
control PWB.
control PWB.
Note
Case 3
Trouble
position/
Cause
position/
Cause
Malfunction caused by
noises
noises
Remedy
Canceled by turning ON/
OFF the power.
OFF the power.
Note
Main
code
code
Sub
code
Title
Inserter/EEPROM trouble
F1
61
Phenomenon
Display
Lamp
Message
Details
Inserter/EEPROM trouble
Data read failure on
turning on the power
Data read failure on
turning on the power
Section
Inserter
Operation
mode
mode
Note
Case 1
Trouble
position/
Cause
position/
Cause
EEPROM trouble
Control circuit runaway
due to noises
Control circuit runaway
due to noises
Remedy
Check that the EEPROM
is properly installed.
Replace the inserter
PWB.
is properly installed.
Replace the inserter
PWB.
Note
Case 2
Trouble
position/
Cause
position/
Cause
Inserter PWB EEPROM
access circuit trouble
access circuit trouble
Remedy
Replace the inserter
PWB.
PWB.
Note
Click on the first or last page to see other AR-M700 (serv.man28) service manuals if exist.