Read Sharp AR-M351U / AR-M451U (serv.man17) Service Manual online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 71
Operation/Procedure
(Various print patterns output) (Table 1)
1) Select PRINT PATTERN with 10-key.
2) Enter the number corresponding to the print pattern to be
printed with 10-key.
3) Press [START] key.
4) Select PRINT START with 10-key.
5) Press [START] key.
(Print condition setting in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
dures.
1) Select TRAY SELECT with 10-key.
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
∗
To adjust the print density, perform the following procedures.
1) Select DENSITY with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
∗
To set the print quantity, perform the following procedures.
1) Select MULTI with 10-key.
2) Enter the print quantity with 10-key.
3) Press [START] key.
∗
To set the print quality mode, perform the following procedures.
1) Select MODE with 10-key.
2) Enter the number corresponding to the print quality mode with
10-key.
3) Press [START] key.
∗
To set the print level, perform the following procedures.
1) Select LEVEL with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
NOTE: In some print patterns, changing the level may not change
the picture quality.
∗
To set duplex/simplex print, perform the following procedures.
1) Select DUPLEX with 10-key.
2) Enter the number corresponding to the operation mode with
10-key.
3) Press [START] key.
(Table 1)
(Note 1) Print pattern
64
64-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the printer section
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
(self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
Item
Operation
0
TRAY SELECT
1. TRAY1
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
Paper feed tray
1: Tray 1
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
1
PRINT START
Print execution (Printing of the set
data is executed.)
data is executed.)
2
PRINT PATTERN
Print pattern (Note 1)
3
DENSITY
Graphic density (Valid only when
No. 79, 80 or 84 is selected.)
No. 79, 80 or 84 is selected.)
4
MULTI
Print quantity
5
MODE
1. STANDARD
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
SAVE
6. SMOOTHING + HALF TONE
7. TONER SAVE + HALF
7. TONER SAVE + HALF
TONE
8. SMOOTHING + TONER
SAVE + HALF TONE
Print mode
1. Standard
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
half tone
6
LEVEL
(Parameter of print image
process)
process)
7
DUPLEX
1. NO
2. YES
2. YES
Duplex
0: NO (Simplex)
1: YES (Duplex)
1: YES (Duplex)
No
Engine
pattern
pattern
Controller
Pattern
Note
1
❍
For off-center adjustment
2
❍
Main scanning direction 1 by 5
3
❍
Main scanning direction 1mm-
pitch
pitch
4
❍
Main scanning direction 3 by 3
5
❍
Sub scanning direction 1 by 1
6
❍
Sub scanning direction 1 by 5
7
❍
Sub scanning direction 2 by 4
8
❍
Sub scanning direction 3 by 3
9
❍
Right oblique 1 by 2
10
❍
Right oblique 1 by 5
11
❍
Right oblique 2 by 4
12
❍
Right oblique 3 by 3
13
❍
Left oblique 1 by 2
14
❍
Left oblique 1 by 5
15
❍
Left oblique 2 by 4
16
❍
Left oblique 3 by 3
17
❍
Dot 1 by 1
18
❍
Dot 3 by 3
19
❍
Dot
20
❍
Solid black
21
❍
Main scanning direction 1 by 1
22
❍
Main scanning direction 5 by 1
23
❍
Main scanning direction 4 by 2
24
❍
Main scanning direction 3 by 3
25
❍
Sub scanning direction 1 by 1
26
❍
Sub scanning direction 5 by 1
27
❍
Sub scanning direction 4 by 2
28
❍
Sub scanning direction 3 by 3
29
❍
Right oblique 2 by 1
30
❍
Right oblique 5 by 1
31
❍
Right oblique 4 by 2
32
❍
Right oblique 3 by 3
33
❍
Left oblique 2 by 1
34
❍
Left oblique 5 by 1
35
❍
Left oblique 4 by 2
36
❍
Left oblique 3 by 3
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.