Read Sharp AR-M276 (serv.man12) User Guide / Operation Manual online
11
GENERAL PROGRAMS
OPERATION SETTINGS
The "OPERATION SETTINGS" are related to basic
operation of the machine and consist of the following
programs:
operation of the machine and consist of the following
programs:
●
AUTO CLEAR SETTING
●
MESSAGE TIME SETTING
●
KEYS TOUCH SOUND
●
TOUCH KEY OPERATION SETTING
●
DISABLE INTERRUPT PRINT JOB
●
STREAM FEEDING MODE
●
DISPLAY LANGUAGE SETTING
●
DISABLE DISPLAY TIMEOUT
●
DISABLING OF TRAY SETTINGS
AUTO CLEAR SETTING
If no action is taken for a certain length of time when
viewing information on finished jobs, jobs in progress,
or stored jobs, the auto clear function activates and
returns the display to the initial screen of copy mode or
the job status screen. AUTO CLEAR SETTING is used
to set the amount of time that must elapse for the auto
clear function to activate. The time can be set from 10
seconds to 240 seconds in increments of 10 seconds,
or the auto clear function can be disabled. (This setting
only operates in copy mode and network scanner
mode.)
viewing information on finished jobs, jobs in progress,
or stored jobs, the auto clear function activates and
returns the display to the initial screen of copy mode or
the job status screen. AUTO CLEAR SETTING is used
to set the amount of time that must elapse for the auto
clear function to activate. The time can be set from 10
seconds to 240 seconds in increments of 10 seconds,
or the auto clear function can be disabled. (This setting
only operates in copy mode and network scanner
mode.)
MESSAGE TIME SETTING
This program is used to set the length of time that
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.
KEYS TOUCH SOUND
This program is used to select whether or not a beep is
sounded when a key is touched, and if sounded, what
type of beep.
The program is also use to select whether or not a
special key touch beep is sounded at the initial point of
a setting.
sounded when a key is touched, and if sounded, what
type of beep.
The program is also use to select whether or not a
special key touch beep is sounded at the initial point of
a setting.
key .... Touch this key to select a low beep
volume. A single beep indicates a valid
key, and a double beep indicates an invalid
key.
key, and a double beep indicates an invalid
key.
key .... Touch this key to select a high beep
volume. A single beep indicates a valid
key, and a double beep indicates an invalid
key.
key, and a double beep indicates an invalid
key.
key .... Touch this key to disable key touch beeps.
Select the [KEYS TOUCH SOUND AT INITIAL POINT]
checkbox to have three long beeps sound (when the
beep volume is set to high) or three short beeps sound
(when the beep volume is set to low) when the initial
point of a setting is reached while selecting basic
settings.
The initial point settings are as follows:
checkbox to have three long beeps sound (when the
beep volume is set to high) or three short beeps sound
(when the beep volume is set to low) when the initial
point of a setting is reached while selecting basic
settings.
The initial point settings are as follows:
TOUCH KEY OPERATION SETTING
These programs are used to set the length of time that
must elapse until a setting is entered after a key is
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled,
only one touch is registered if key is touched
continuously.
must elapse until a setting is entered after a key is
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled,
only one touch is registered if key is touched
continuously.
DISABLE INTERRUPT PRINT JOB
(When the printer function is enabled)
When printing in printer mode, printing can be paused
to enble an interrupt copy job to be performed.
Enable this program if you wish to prevent pausing of
printing for interrupt copy jobs.
to enble an interrupt copy job to be performed.
Enable this program if you wish to prevent pausing of
printing for interrupt copy jobs.
KEY OPERATOR PROGRAMS
OPERATION SETTINGS
MESSAGE TIME SETTING
KEYS TOUCH SOUND
OK
1/3
6sec
AUTO CLEAR SETTING
60sec
Mode
Initial point (set from initial screen)
Copy mode
Ratio: 100%
Exposure: 3
Exposure: 3
Fax mode
Exposure: 3
Network scanner
mode
mode
Exposure setting: 3
KEY OPERATOR PROGRAMS
KEYS TOUCH SOUND
KEYS TOUCH SOUND AT INITIAL POINT
KEYS TOUCH SOUND
OK
Click on the first or last page to see other AR-M276 (serv.man12) service manuals if exist.