AR-FX8. Service manual - Sharp Copying Equipment Service Manual (repair manual). Page 66

Read Sharp AR-FX8 Service Manual online

AR-FX8  MACHINE OPERATION  7 - 4
5. Trouble codes
*
Only the FAX-related codes are extracted. 
A. Details of trouble codes
MAIN SUB
F6
00
Content
Communication trouble (ICU detection) 
between ICU and FAX
Details
Communication establishment error/Fleming/
Parity/Protocol error
Cause
Slave unit PWB connector disconnection
Harness abnormality between slave unit 
PWB and ICU PWB.
Slave unit PWB mother board connector pin 
breakage
Slave unit ROM abnormality/No ROM/
Reverse insertion of ROM/ROM pin 
breakable
Check & 
Remedy
Check connector harness between slave unit 
PWB and ICU PWB.
Check grounding of machine.
Check slave unit PWB ROM.
01
Content
FAX expansion flash memory abnormality 
(ICU detection)
Details
Expansion flash memory with Address data 
backup data is installed. 
Cause
Address data backup data is detected in 
expansion flash memory.
Expansion flash memory in which Address 
data are backed up with SIM 66-19 is 
installed.
Check & 
Remedy
Restore backup data to Address data with 
SIM 66-20, and clear expansion flash 
memory with SIM 66-10. 
If data are unnecessary, clear expansion 
flash memory with SIM 66-10.
04
Content
FAX modem operation abnormality
Details
FAX PWB modem chip operation 
abnormality
Cause
The boot test pin in the FAX PWB is shorted 
and normal operation is tried.
Modem chip operation abnormality in FAX 
PWB
Check & 
Remedy
Turn on the power again without shorting the 
boot test pin in the FAX PWB.
Replace FAX PWB.
20
Content
FAX write protect cancel
Details
The write protect DIP switch on the ICU PWB 
is released (canceled).
Cause
The FAX write protect DIP switch is set to the 
FAX write enable position.
FAX PWB trouble
Check & 
Remedy
Check the write protect DIP switch on the 
ICU PWB. 
Replace the FAX PWB and the ICU PWB. 
F6
21
Content
Abnormal combination of the TEL/LIU PWB 
and the FAX soft switch
Details
Abnormal combination of the TEL/LIU PWB 
and the FAX PWB information (soft switch)
Cause
Erroneous destination of the installed TEL/
LIU PWB
Erroneous FAX PWB information 
(soft switch)
Abnormal TEL/LIU PWB
Check & 
Remedy
Check the destination of the TEL/LIU PWB
Check the FAX PWB information 
(soft switches).
Replace the TEL/LIU PWB.
F6
97
Content
FAX-BOX incompatibility trouble
Details
The FAX-BOX PWB is not one for the AR-
FX8.(FAX detection)
If the FAX-BOX modem controller PWB 
information (hard detection) is not for the AR-
FX8, it is judged as an error.
Cause
Because the FAX-BOX modem controller 
PWB information (hard detection) is not for 
the AR-FX8. (The modem controller PWB for 
the AR-FX5 or the AR-FX6 is used.)
Check & 
Remedy
Check the FAX-BOX modem controller PWB.
Replace it with a modem controller PWB for 
the AR-FX8.
98
Content
Abnormal combination of the FAX-BOX 
destination information and the machine 
destination information
Details
Abnormal combination of the FAX-BOX 
destination information and the machine 
destination information
Cause
Combination between the destination 
information saved in the EEPROM on the 
FAX-BOX and the machine destination 
information (set with SIM26-6) is abnormal.
Check & 
Remedy
Check the FAX-BOX destination.
Check the machine destination setup 
(SIM26-6).
Use the proper combination of the machine 
and the FAX-BOX.
F7
01
Content
FAX board EEPROM read/write error
Details
EEPROM access error (read/write)
Cause
EEPROM trouble
FAX PWB EEPROM access circuit trouble
Check & 
Remedy
Replace FAX PWB.
U1
01
Content
Battery abnormality (on the ICU PWB)
Detail
Backup SRAM battery voltage fall
Cause
Battery life
Battery circuit abnormality
Check 
and 
remedy
Check that the battery voltage is about 2.5V 
or above.
Check the battery circuit. 
02
Content
RTC read abnormality 
(common with FAX, on ICU PWB)
Details
The value read from RTC on ICU PWB is 
[EE]h (abnormal).
Cause
RTC circuit abnormality
Battery voltage fall
Battery circuit abnormality
Check & 
Remedy
Set the time again with key operation, and 
check that time advances properly.
Check RTC circuit.
Check that battery voltage is about 2.5V or 
above.
Check battery circuit. 
MAIN SUB
Page of 74
Display

Click on the first or last page to see other AR-FX8 service manuals if exist.