Read Sharp AR-FX13 Service Manual online
AR-FX13 FAX SOFT SWITCH 5 - 26
SW24 No.1, No.2 Inhibited to use
SW24 No.3, No4 Specified number reception (ANTI
JUNK FAX)
JUNK FAX)
Used to set whether the FAX receive rejection function is made valid
or not for registered FAX numbers.
or not for registered FAX numbers.
Default: 0 0 (Not set.)
SW24 No.5 Inhibited to use
SW24 No.6 Document output setup in reception
Used to set the document output procedure; whether all the received
documents are collectively outputted after completion of reception or
every page is outputted when it is received.
documents are collectively outputted after completion of reception or
every page is outputted when it is received.
SW24 No.7 Inhibited to use
SW24 No.8 Automatic reduction print
Used to set whether automatic reduction print is performed or not so
that a document longer than the fixed size and smaller than the auto-
matic reduction line number setting is printed on fixed size paper.
that a document longer than the fixed size and smaller than the auto-
matic reduction line number setting is printed on fixed size paper.
Default: 1 (Allow)
SW25 No.1–No.4 Automatic reduction rate setup
Used to set automatic reduction rate when automatic reduction print
is valid.
is valid.
Default: 10%
SW25 No.5, No.6 Transmission end sound tone
Used to set transmission end sound tone in transmission.
Default: 0 1 (1000Hz)
SW25 No.7, No.8 Reception end sound tone
Used to set reception end sound tone in reception.
Default: 0 1 (1000Hz)
SW26 No.1 Read completion sound
Used to set whether buzzer sound is made or not when scan is com-
pleted.
pleted.
In manual send or when scan is completed in direct send, buzzer
sound is not made.
sound is not made.
Default: 0 (1sec)
SW26 No.2 Inhibited to use
SW26 No.3, No.4 Speaker volume setup
Used to set speaker volume.
The following sounds are the targets of this setting.
• Alarm sound
• Send end sound
• Receive end sound
• Scan end sound
Default: 0 1 (Small)
SW26 No.5–No.8 Inhibited to use
SW27 No.1–No.6 Inhibited to use
SW27 No.7, No.8 Recording paper tray selection
Used to select the recording paper tray used by FAX.
Valid only when two cassettes are installed.
Default: 0 0 (AUTO)
SW28 No.1–No.8 Inhibited to use
SW29 No.1–No.4 Number of auto switch calls of manual
reception
reception
→ auto reception
Used to set the number of calls to switch to auto receive in manual
receive mode.
receive mode.
When set to 0, switch to auto receive is not made.
Default: 0 time
SW29 No.5–No.8 Setup of number of times of call rings
Used to set the number of calls before starting reception in auto
receive mode.
receive mode.
Setting is made in binary input.
Default: 2 times
SW30 No.1 Report output when canceling
Used to set whether the user cancel report is outputted or not when
send is canceled during document send.
send is canceled during document send.
Default: 0 (Not output)
SW30 No.2–No.4 Inhibited to use
SW30 No.5 Default data, sender print
Used to set whether sender information (registered in the sender
registration), sending date, and time are printed on the upper edge
of send document or not.
registration), sending date, and time are printed on the upper edge
of send document or not.
Default: 1 (ON)
SW30 No.6 Inhibited to use
SW30 No.7 Date/sender print position setup
Used to set whether date/sender information is printed inside the
document area or outside the document area.
document area or outside the document area.
Default: 0 (Outside of document)
SW30 No.8 Inhibited to use
SW31 No.1, No.2 Report output (in transmission)
Used to set whether communication report is outputted or not after
completion of sending (excluding sequential broadcast and sequen-
tial send request).
completion of sending (excluding sequential broadcast and sequen-
tial send request).
Default: 1 0 (Only when transmission is failed.)
SW31 No.3, No.4 Report output (In broadcast and
sequential send request)
sequential send request)
Used to set whether communication report is outputted or not after
completion of sending (sequential broadcast and sequential send
request).
completion of sending (sequential broadcast and sequential send
request).
Default: 0 1 (All print)
SW31 No.5, No.6 Report output (in reception)
Used to set whether communication report is outputted or not in
reception.
reception.
Default: 0 0 (Print inhibited)
SW31 No.7, No.8 Contents of send document are
printed in memory send
printed in memory send
Used to set whether part of send document is printed on the commu-
nication report or not in memory send.
nication report or not in memory send.
Default: 1 0 (Only the address to which transmission is failed)
SW32 No.1–No.4 Distinctive ringing (North America,
Australia, New Zealand)
Australia, New Zealand)
Used to set the ringing pattern as FAX reception.
Default: 0 0 0 0 (OFF)
SW32 No.5 Inhibited to use
SW32 No.6 Index print setup
Used to set whether the index is printed when outputting received
document or not.
document or not.
Default: 0 (Not print)
SW32 No.7, No.8 Inhibited to use
SW33 No.1 Page number print setup
Used to set whether the page number is added to the sender infor-
mation print or not.
mation print or not.
Default: 1 (Yes)
SW33 No.2–No.7 Inhibited to use
Default: 0 (Output after reception of every page) (North America) /
1 (Collective output after completion of reception) (Other
than North America)
than North America)
Click on the first or last page to see other AR-FX13 service manuals if exist.