Read Sharp AR-122E (serv.man55) User Guide / Operation Manual online
27
6
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
Indication
Cause and remedy
Page
Developer
replacement
required indicator
replacement
required indicator
Steadily
lit
lit
Developer is required. contact your authorised
service representative.
service representative.
31
Toner cartridge
replacement
required indicator
replacement
required indicator
Steadily
lit
lit
Replacement of Toner cartridge will be needed
soon. Prepare a new cartridge. (AR-152T)
soon. Prepare a new cartridge. (AR-152T)
21
Blinking
Toner cartridge must be replaced. Replace it
with a new one. (AR-152T)
with a new one. (AR-152T)
21
Misfeed indicator
Blinking
A misfeed has occurred. Remove the misfed
paper referring to the description of "MISFEED
REMOVAL".
paper referring to the description of "MISFEED
REMOVAL".
28
Maintenance
indicator
indicator
Steadily
lit
lit
Service by an authorised SHARP service
technician is required.
technician is required.
31
Power save indicator is
steadily lit.
steadily lit.
The unit is in the preheat mode. Press any key to
cancel the preheat mode.
cancel the preheat mode.
18
The unit is in the auto power shut-off mode.
Press the start (
Press the start (
) key to cancel the auto power
shut-off mode.
18
The paper tray indicator is
blinking.
blinking.
The paper tray is not installed properly. Push the
tray into the unit securely.
tray into the unit securely.
–
"CH" is blinking in the
display.
display.
The toner cartridge is not installed. Check if the
cartridge is installed. If "CH" is blinking even if a
cartridge is installed properly, contact your
SHARP service centre immediately.
cartridge is installed. If "CH" is blinking even if a
cartridge is installed properly, contact your
SHARP service centre immediately.
21
"CH" is steadily lit in the
display.
display.
Side cover is open. Close the side cover
securely by pressing the round projections near
the side cover open button.
securely by pressing the round projections near
the side cover open button.
–
"P" is blinking in the display.
The paper tray is empty.
Load paper.
Load paper.
8
A misfeed has occurred in the paper tray, single
bypass. Remove the misfed paper.
bypass. Remove the misfed paper.
28
Paper tray is not securely installed. Push the tray
in securely.
in securely.
–
A letter and a number appear
alternately.
alternately.
The scan head locking switch is locked. Unlock
the scan head locking switch and turn the power
switch off/on.
the scan head locking switch and turn the power
switch off/on.
–
A letter and a number appear
alternately.
alternately.
The unit will not function. Turn the power switch
off and then switch it on, and if there is again an
error, remove the power cord from the outlet, and
contact your authorized service representative.
off and then switch it on, and if there is again an
error, remove the power cord from the outlet, and
contact your authorized service representative.
–
A letter and a number appear
alternately.
alternately.
You will not be able to use the toner cartridge
anymore (Toner Cartridge End of life). Contact
your authorised service representative.
anymore (Toner Cartridge End of life). Contact
your authorised service representative.
–
Click on the first or last page to see other AR-122E (serv.man55) service manuals if exist.