Read Sharp AL-1000 / AL-1010 (serv.man12) Service Manual online
Main code
Sub code
Contents
50
1
Lead edge position and paper lead edge/rear edge void adjustment
Used to adjust the copy image position on copy paper and the lead edge/rear edge void amounts. Performed by
adjusting the scanning start position and print start position (resist roller ON timing) in 100%.
(Operation/Procedure)
1. When this simulation is executed, the current set value is displayed in two digits. (Center value: 50)
2. When the copy mode select key is pressed, the setting mode and the setting display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows.
3. Enter the adjustment value with the 10-key and press the START key. Then the set value is stored and copy is
made. (An increase of 1 in the set value corresponds to 0.1mm shift.)
4. Press the clear key to store the set value and exit the simulation.
Used to adjust the copy image position on copy paper and the lead edge/rear edge void amounts. Performed by
adjusting the scanning start position and print start position (resist roller ON timing) in 100%.
(Operation/Procedure)
1. When this simulation is executed, the current set value is displayed in two digits. (Center value: 50)
2. When the copy mode select key is pressed, the setting mode and the setting display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows.
3. Enter the adjustment value with the 10-key and press the START key. Then the set value is stored and copy is
made. (An increase of 1 in the set value corresponds to 0.1mm shift.)
4. Press the clear key to store the set value and exit the simulation.
Adjustment mode
Lamps ON
Print start position
AE lamp
Image lead edge void amount
TEXT lamp
Image scanning start position (Scanner)
PHOTO lamp
Image rear edge void amount
AE, TEXT, PHOTO lamps
10
Center offset adjustment
(Outline)
Used to adjust the copy image position on copy paper and the center offset position in scanning an original.
Performed by changing the set values of the SCAN LEFT MARGIN register and the PRINT LEFT MARGIN
register of ASIC.
(Operation/Procedure)
1. When this simulation is executed, the current set value is displayed.
2. In a machine with the multi paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
In a machine with the single paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows:
3. Enter the adjustment value with the 10-key and press the SORT key. Then the set value is stored and a copy
is made. (An increase of 1 in the set value corresponds to 0.1mm shift.)
4. Press the clear key to store the set value and exit the simulation.
(Outline)
Used to adjust the copy image position on copy paper and the center offset position in scanning an original.
Performed by changing the set values of the SCAN LEFT MARGIN register and the PRINT LEFT MARGIN
register of ASIC.
(Operation/Procedure)
1. When this simulation is executed, the current set value is displayed.
2. In a machine with the multi paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
In a machine with the single paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows:
3. Enter the adjustment value with the 10-key and press the SORT key. Then the set value is stored and a copy
is made. (An increase of 1 in the set value corresponds to 0.1mm shift.)
4. Press the clear key to store the set value and exit the simulation.
* Machine with the multi manual paper feed unit installed
Adjustment mode
Lamps ON
Print center offset (main cassette paper feed)
AE, main cassette lamp
Print center offset (2nd cassette paper feed)
AE, 2nd cassette lamp
Print center offset (Manual paper feed)
AE, manual feed lamp
OC/original center offset
AE, TEXT lamp
SPF/Original center offset
AE, TEXT, PHOTO lamp
* Machine with the single manual paper feed unit installed
Adjustment mode
Lamps ON
Print center offset (main cassette paper feed)
AE, main cassette lamp
Print center offset (Manual paper feed)
AE (Blink)
OC/original center offset
AE, TEXT lamp
SPF/Original center offset
AE, TEXT, PHOTO lamp
51
2
Resist amount adjustment
(Outline)
Used to adjust the contact pressure of paper onto the copier resist roller and the SPF resist roller.
(Operation/Procedure)
1. When this simulation is executed, the currently set value is displayed.
2. In a machine with the multi paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
In a machine with the single paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows:
3. Enter the adjustment value with the 10-key and press the SORT key. Then the set value is stored and a copy
is made.
4. Press the clear key to store the set value and exit the simulation.
(Outline)
Used to adjust the contact pressure of paper onto the copier resist roller and the SPF resist roller.
(Operation/Procedure)
1. When this simulation is executed, the currently set value is displayed.
2. In a machine with the multi paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
In a machine with the single paper feed unit installed, press the copy mode select key, and each setting mode
and display are changed sequentially.
* The selected adjustment mode is indicated by the lamps as follows:
3. Enter the adjustment value with the 10-key and press the SORT key. Then the set value is stored and a copy
is made.
4. Press the clear key to store the set value and exit the simulation.
AL-1000/1010
10-9
Click on the first or last page to see other AL-1000 / AL-1010 (serv.man12) service manuals if exist.