PN-G655E (serv.man3) - Sharp Monitor Service Manual (repair manual). Page 6

OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION

1 – 4

■ Remote Control Unit

■ Installing the batteries

1) Press the cover gently and slide it in the direction of the arrow.

2) See the instructions in the compartment and put in the supplied bat-

teries (2 R-6 batteries) with their plus (+) and minus (-) sides ori-
ented correctly.

3) Close the cover.

Note:

•  The supplied batteries (2 R-6 batteries) may become exhausted

faster depending on the storage condition. It is recommended that

you replace them with new batteries (commercially available) ear-

lier than specified.

•  If you will not use the remote control for a long time, remove the

batteries.

•  Use manganese or alkaline batteries only.

■ Remote control operation range

The operation range of the remote control unit is approx. 5m at an angle
of approx 10° from the centre to the top/bottom/right/left of the remote
control sensor.

Caution:

•  Do not expose the remote control unit to shock by dropping or step-

ping on it. This could lead to a malfunction.

•  Do not expose the remote control unit to liquids, and do not place it

in an area with high humidity.

•  The remote control unit may not work properly if the remote control

sensor is under direct sunlight or strong lighting. 

•  Objects between the remote control unit and the remote control

sensor may prevent proper operation.

•  Replace the batteries when they run low as this may shorten the

remote control’s operation range.

•  If a fluorescent light is illuminated near the remote control unit, it

may interfere with proper operation.

•  Do not use it with the remote control of other equipment such as air

conditioner, stereo components, etc.

1Signal transmitter

2POWER button

3MUTE button

Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the previous
level.

4VOL 

Pressing 

 or 

 displays the VOLUME menu when the menu

screen is not displayed.
Press 

 or 

 to adjust the volume of the sound.

* If you do not press any buttons for about 4 seconds, the VOLUME

menu automatically disappears.

+

−

Pressing 

 or 

 displays the BRIGHT menu when the menu

screen is not displayed.
Press 

 or 

 to adjust the brightness.

* If you do not press any buttons for about 4 seconds, the BRIGHT

menu automatically disappears.

S/T/W/ X) buttons

5DISPLAY button

Displays monitor information. The display disappears when this but-
ton is pressed again or disappears automatically after approximately

15 seconds.

6MODE button

Each time you press this button, the color mode changes in the fol-
lowing order:

• STD (Standard) 

JVIVID J sRGB

 

J STD...

* sRGB applies to PC input only.

sRGB is international standard of color representation specified by

IEC (International Electrotechnical Commission).

Color conversion is made in taking account of liquid crytal’s charac-
teristics and represents color tone close to its original image.

7INPUT button (Input mode selection)

The menu is displayed. Press 

 or 

 to select the input mode,

and press 

 to enter.

* You can select the input terminal by pressing the input switch of

the monitor.

Input mode

Video

Audio

PC1 DIGITAL

*1

PC1 input terminal

PC audio input
terminal

PC2 ANALOG

PC2 input terminal

PC3 ANALOG

*2

PC3 input terminals

AV1 DIGITAL

*1

AV1 input terminal

AV  audio  inpu t
terminals

AV2 COMPONENT

*2

AV2 input terminals

AV3 VIDEO

AV3 input terminal

1

2

3

4

5

6

7

8

9

*1 Select the terminal for DVI SELECT.
*2 Select the terminal for BNC SELECT.

8MENU button

Displays and turns off the menu screen

9SIZE button

The menu is displayed.

Press 

 or 

 to select the screen size.

°

Remote control sensor

5 m

5 m

5 m

10

°

10