Read Sharp LL-T1610W (serv.man11) Service Manual online
7. Replace the stand cover.
8. Replace the rear cover.
9. Place power plug into AC outlet.
1-2. CONNECTING THE MONITOR TO A
COMPUTER (PC ETC.)
For analog RGB output terminal
Connecting to a computer with analog RGB output. When connecting,
ensure that both the monitor and computer are switched off.
ensure that both the monitor and computer are switched off.
Notes:
•
If using the monitor for the first time or after having
changed the system settings during use, perform an auto-
matic screen adjustment.
changed the system settings during use, perform an auto-
matic screen adjustment.
•
Be careful not to overly bend the cable or add extension
cords as this could lead to malfunction.
cords as this could lead to malfunction.
•
When connecting to a notebook, if the notebook com-
puter’s screen is set so that it is displaying at the same
time, the MS-DOS screen may not be able to display
properly. In this case, change the settings so that only the
monitor is displaying.
puter’s screen is set so that it is displaying at the same
time, the MS-DOS screen may not be able to display
properly. In this case, change the settings so that only the
monitor is displaying.
Note: If connecting to the Sun Ultra series, a conversion adapter
(purchased separately) may be required.
For digital RGB output terminal
Connecting to a computer with digital RGB output. When connecting,
ensure that both the monitor and computer are switched off.
ensure that both the monitor and computer are switched off.
Notes:
•
A computer with an output terminal conforming to DVI
(DVI-D24 pin or DVI-I29 pin) and with SXGA output capa-
bility can be connected here. Depending on the type of
computer to be connected, the display may not work cor-
rectly. In order to connect, it is necessary to purchase a
digital signal cable separately. (model name: NL-C01E)
(DVI-D24 pin or DVI-I29 pin) and with SXGA output capa-
bility can be connected here. Depending on the type of
computer to be connected, the display may not work cor-
rectly. In order to connect, it is necessary to purchase a
digital signal cable separately. (model name: NL-C01E)
•
Be careful not to overly bend the cable or add extension
cords as this could lead to malfunction.
cords as this could lead to malfunction.
1. Remove the rear cover and the stand cover.
To remove them follow steps 1 and 2 of Connecting the monitor
to a power source.
to a power source.
2. Attach the digital signal cable (sold separately from monitor).
If you are not using the analog signal cable, you can remove it.
Loosen all screws on the plug and disconnect it.
Loosen all screws on the plug and disconnect it.
9
10
Run the analog signal
cable through here.
cable through here.
12
11
Analog signal cable
Computer
Analog RGB output terminal (mini D-sub 15 pin
with 3 rows)
Firmly insert the plug then tighten the screws
each side.
with 3 rows)
Firmly insert the plug then tighten the screws
each side.
If connecting to a D-sub 15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter (to
be purchased separately) to the analog signal cable.
Macintosh, attach a Macintosh conversion adapter (to
be purchased separately) to the analog signal cable.
Macintosh
conversion adapter
conversion adapter
Analog signal cable
After connecting the adapter, tighten the
screws on each side to fix into place
After connecting the adapter, tighten the
screws on each side to fix into place
Digital signal input terminal (DV-D24 pin)
Firmly insert the plug than tighten the screws
each side.
Firmly insert the plug than tighten the screws
each side.
Run cable through hole
Digital signal cable
Analog signal cable
Click on the first or last page to see other LL-T1610W (serv.man11) service manuals if exist.