LL-T1511A (serv.man3). Connection, adjustment, operation, and functions. - Sharp Monitor Service Manual (repair manual). Page 5

The brightness can be changed to any one of three settings.

Carry out the commands without the On Screen Display (OSD) Menu
displayed. If the OSD Menu is displayed, press the BRIGHT button
and begin when it has disappeared. (You can also make it disappear
by pressing the MENU button several times.)

1. Without the OSD Menu being displayed, push the BRIGHT button.

2. Press the BRIGHT button several times to choose the brightness.

3. Press the MENU button.

The OSD will disappear.

Notes:

•

The OSD Menu automatically disappears several seconds after
the last command.

•

If [AUTO] is selected, the backlight brightness changes auto-
matically for use in different surroundings.

•

After selecting the brightness (LOW, MID, HIGH), fine adjust-
ments can be made using the   button or the   button.

Carry out the commands without the On Screen Display (OSD) Menu
displayed. If the OSD Menu is displayed, press the BRIGHT button
and begin when it has disappeared. (You can also make it disappear
by pressing the MENU button several times.)

1. Without the OSD Menu being displayed, press the   button or the

 button. The BRIGHT bar will appear at the bottom section of the

screen.

2. Adjust by pressing the   button (darker) or the   button (lighter).

3. Press the MENU button.

The BRIGHT button will disappear.

Note: The BRIGHT bar automatically disappears several seconds

after the last command.

Fine adjustments can be made using On Screen Display (OSD) Menu
provided.

MENU 1:

ADJUSTMENT
Clock, Phase, H-POS (horizontal positioning) and V-POS
(vertical positioning)

MENU 2:

GAIN CONTROL
BLACK LEVEL, CONTRAST, DISPLAY COLORS

MENU 3:

WHITE BALANCE
WHITE BALANCE (color tone)

MENU 4:

MODE SELECT
OSD H-POSITION (OSD horizontal position), OSD V-PO-
SITION (OSD vertical position), 400LINES (resolution),
SCALING (level of scaling)

1. Display an image that makes the entire screen very bright. If using

Windows, you can open and use the Adjustment Pattern on the
accompanying Monitor Settings Adjustment Disk.

2. Press the MENU button.

The ADJUSTMENT Menu will be displayed. At this point relevant
menu options can be adjusted.

Each time the MENU button is pressed, the next menu is selected.
(MENU 1 

 2 

 3 

 4 

 OSD Menu disappears)

Notes:

1. The OSD Menu automatically disappears approximately 15

seconds after the last command.

2. This explanation is based on using the Adjustment Pattern (for

Windows) to make adjustments.

3. Press the BRIGHT button to make the OSD Menu disappear.

MANUAL: Individual menu options are manually adjusted.

AUTO:

Every menu option is automatically adjusted

Notes:

•

Press the   button to select AUTO.

•

To choose a menu option: SELECT button

•

To go to MENU 2:

MENU button

The figure below demonstrates how to adjust so that vertical flicker
noise is not emitted. (

buttons)

The figure below demonstrates how to adjust so that horizontal flicker
noise is not emitted. (

 buttons)

Note: Adjustments to PHASE should be made only after CLOCK has

been correctly set.

[

 

]  

LOW

MID

HIGH

 

 

[

 

]  

AUTO

LOW

MID

[

]

[

]

A

A

A

C

C

D

E

H

V

H

H

J

K

M

N

L

O

O

O

P

P

S

S

S

T

T

U

U

8

V

1

4

6

4

H

6

7

0

8

0

5

6 0

1

5

z

0

-

O

P

-

:

: 4

H

E

T

S

x

2

k

z

[

]

A

A

A

C

C

D

E

H

V

H

H

J

K

M

N

L

O

O

O

P

P

S

S

S

T

T

U

U

8

V

1

4

6

4

H

6

7

0

8

0

5

6 0

1

5

z

0

-

O

P

-

:

: 4

H

E

T

S

x

2

k

z

Vertical flicker noise

Horizontal flicker noise