Read Sharp LL-172G Service Manual online
LL-172A-W/B/LL-172G-W/B
CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS
2 – 11
12.SETTING [PRODUCT INFORMATION] AFTER
LOADING EDID PROGRAM
12-1. Turn off the main power supply and then turn it on.
If the LEDs (green, orange) come on, press the [POWER] button to turn
them off.
them off.
12-2. Execute All reset.
Hold down the [MENU] + [MODE] buttons and press the [POWER] button.
All reset is executed and the [ENGLISH] OSD is displayed.
All reset is executed and the [ENGLISH] OSD is displayed.
12-3. Check the Product information.
Hold down the [MODE] button and press the [POWER] button.
The former model name, serial number and the usage time are displayed.
The former model name, serial number and the usage time are displayed.
12-4. If the model name or serial number are different from
that on the said monitor, it is advisable to set the [Prod-
uct information] from EDID data using the following
manner:
uct information] from EDID data using the following
manner:
12-4-1. [Set Product information again]
Hold down the [MODE] + [
3
] buttons and press the [POWER] button.
If the above screen is displayed, press both the [
1
] + [
3
] buttons
simultaneously.
12-4-2. If the model name and serial number of the EDID data
that has been read are the LL-172B and 3T000018, the fol-
lowing information is displayed.
lowing information is displayed.
Check the model name and serial number on the screen against
those on the name plate on the said monitor and make sure they
are the same before pressing the MENU button.
those on the name plate on the said monitor and make sure they
are the same before pressing the MENU button.
12-6. Check Product information again.
Hold down the [MODE] button and press the [POWER] button.
The model name, serial number and usage time are shown on the
above screen.
above screen.
12-7. Press the [POWER] button to shut off the software
power supply.
12-8. Turn off the AC power supply using the AC power
supply switch.
[Supplementary explanation]
o
How to set the printer port I/O address to 378.
1. Open the Control Panel and then click System.
2. Open the Device Manager tab and select the Display by Type radio
button.
3.
Click the "+" mark at the left of Port (COM/LPT) and check that there is
"Printer Port (LPT1), " "ECP Printer Port (LPT1)" or the like in the list.
"Printer Port (LPT1), " "ECP Printer Port (LPT1)" or the like in the list.
4. Open the Properties of Printer Port (LPT1), and then open the
Resource tab.
5. Deselect the "Auto Configuration" check box and select "Basic Con-
figuration."If the setting of "I/O Range" is 0378-037F, there is no
need to change the setting.
o
In this writing procedure, the folder to which the files are copied is set
to c:\FG. However, you can set the location of the folder anywhere in
to c:\FG. However, you can set the location of the folder anywhere in
the hard disk if all files are copied in the same folder.
Model name
Serial number
Usage time hours
Serial number
Usage time hours
Product information
: LL-172A-W
: 3T003219
: 00012
: 3T003219
: 00012
MODEL S/N
DISCONNCT ANALOG RGB CABLE
PRESS BOTH [<-] AND [->] KEY
PRESS BOTH [<-] AND [->] KEY
MODEL S/N
DISCONNCT ANALOG RGB CABLE
PRESS BOTH [<-] AND [->] KEY
PRESS BOTH [<-] AND [->] KEY
L
2
Product information
: LL-172A-B
: 3T000018
: 00012
: 3T000018
: 00012
Model name
Serial number
Usage time hours
Serial number
Usage time hours
Click on the first or last page to see other LL-172G service manuals if exist.