Read Sharp R-772M (serv.man2) Service Manual online
17
The touch control section consists of the following units as
shown in the touch control panel circuit.
shown in the touch control panel circuit.
(1) Key Unit
(2) Control Unit (The Control unit consists of Power unit
(2) Control Unit (The Control unit consists of Power unit
and CPU unit.)
The principal functions of these units and signals commu-
nicated among them are explained below.
nicated among them are explained below.
Key Unit
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit from P40, P41, P72, P73
P74, P75, P76 and P77.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through P44 - P47
to perform the function that was requested.
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit from P40, P41, P72, P73
P74, P75, P76 and P77.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through P44 - P47
to perform the function that was requested.
Control Unit
Control unit consists of LSI, power source circuit, synchro-
nizing signal circuit, ACL circuit, buzzer circuit, relay
circuit, temperature measurement circuit, indicator circuit
and back light circuit.
Control unit consists of LSI, power source circuit, synchro-
nizing signal circuit, ACL circuit, buzzer circuit, relay
circuit, temperature measurement circuit, indicator circuit
and back light circuit.
1) LSI
This LSI controls the temperature measurement sig-
nal, key strobe signal, relay driving signal for oven
function and indicator signal.
nal, key strobe signal, relay driving signal for oven
function and indicator signal.
2) Power Source Circuit
This circuit generates voltage necessary in the control
unit.
unit.
Symbol
Voltage
Application
VC
-5.2V
LSI(IC1)
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
order to compose a basic standard time in the clock
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
circuit. It accompanies a very small error because it
works on commercial frequency.
works on commercial frequency.
4) ACL
A circuit to generate a signal which resets the LSI to the
initial state when power is supplied.
initial state when power is supplied.
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (key touch sound and completion
sound).
audible sounds (key touch sound and completion
sound).
6) Door Sensing Switch (Stop Switch)
A switch to "tell" the LSI if the door is open or closed.
7) Relay Circuit
To drive the magnetron, grill heating element, bottom
heating element, fan motor, turntable motor, touch
control transformer and light the oven lamp.
heating element, fan motor, turntable motor, touch
control transformer and light the oven lamp.
8) Back Light Circuit
A circuit to drive the back light (Light emitting diodes
LD1 - LD10).
LD1 - LD10).
9) Indicator Circuit
This circuit consists 7-digits, 39-segments and 3-com-
mon electrodes using a Liquid Crystal Display.
mon electrodes using a Liquid Crystal Display.
10) Temperature Measurement Circuit : (OVEN
THERMISTOR)
The temperature in the oven cavity is sensed by the
thermistor. The variation of resistance according to
sensed temperature is detected by the temperature
measurement circuit and the result applied to LSI.
The LSI uses this information to control the relay
and display units.
The temperature in the oven cavity is sensed by the
thermistor. The variation of resistance according to
sensed temperature is detected by the temperature
measurement circuit and the result applied to LSI.
The LSI uses this information to control the relay
and display units.
DESCRIPTION OF LSI
LSI(IZA965DR)
The I/O signal of the LSI(IZA965DR) are detailed in the following table.
The I/O signal of the LSI(IZA965DR) are detailed in the following table.
Pin No.
Signal
I/O
Description
1
C1
IN
Terminal not used.
2
VL1
IN
Power source voltage input terminal.
Standard voltage for LCD.
Standard voltage for LCD.
3
AN7
IN
Terminal to change the on timing of the cook relay (RY2).
4-5
AN6-AN5
IN
Heating constant compensation terminal.
6
AN4
OUT
Terminal not used.
7
AN3
IN
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the
thermistor, this input is converted into temperature by the A/D converter built into
the LSI.
By inputting DC voltage corresponding to the temperature detected by the
thermistor, this input is converted into temperature by the A/D converter built into
the LSI.
Click on the first or last page to see other R-772M (serv.man2) service manuals if exist.