R-393 (serv.man7). EBR4800 Built in kit instructions - Sharp Home Appliance User Guide / Operation Manual. Page 2

2

2

A32867,EBR-4800

2

1. (For U.K. use)

A cut-out will have to be provided in the side of the kitchen cabinet for the plug of the oven.

N.B.The mains plug must be accessible after installation or an all-pole switch disconnection must be

provided with a contact separation of at least 3 mm in each pole.

(For Continental use)

The electric outlet must be installed at 150 mm high from the floor of the built-in cabinet and at 50 mm

from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be accessible after

installation or the oven must be connected to an electric circuit provided with an all-pole switch (contact

gap no less than 3 mm) to disconnect the oven in case of danger. A safety-device like a fuse in the

installation may be used as a switch.

2. Remove the built-in kit from the package.
3. Set the spacing brackets 

1

 on the shelf along the right and left walls of the kitchen cabinet, keeping

a distance of 7mm between the front end of the shelf and the spacing brackets, and attach them with
the four screws 

9

, as shown in Fig. 1.

Caution:

The arrow marks on each spacing bracket should be pointing towards you.

4. (Carry out this step 4 only for B type models)

Remove the screw 

F

 holding the air duct 

G

 to the rear of the oven as shown in Fig. 3.  And release the

tab of the air duct 

G

 from the slit of the rear of the oven.  Then remove the air duct 

G

 from the oven.

5. (Carry out this step 5 only for B type models)

Remove the screw 

H

 holding the back plate 

I

 to the rear of the oven as shown in Fig. 3. And release the

tabs of the back plate 

I

 from the slits of the rear of the oven.

6. Remove the one screw 

E

 from the oven as shown in Fig. 3.

7. Insert the tab of the exhaust duct 

2

 into the slit of the rear of the oven.  And install the exhaust duct 

2

to the rear of the oven with one screw 

0

 as shown in Fig. 4.

8. Let the power supply cord pass through the hole of the lower side of the intake duct 

3

 as shown in Fig. 4.

9. Install the intake duct 

3

 to the rear of the oven with two screws 

0

 and 

E

 (removed at step 6) as shown

in Fig. 4.
Caution:

Avoid pinching the power supply cord between the oven and the intake duct 

3

.

10. Remove the backing paper from the three cushions 

4

, 

5

 and 

6

.  Attach the cushion

4

 at the top of the

intake duct 

3

 and attach the cushions 

5

 and 

6

 at the top of the oven as shown in Figs 5-a and 5-b.

11. (For U.K. use)

Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the power supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.

12. Connect the oven to the power supply.

Caution: a. In U.K., connect the oven to the power supply 230-240 V, 50 Hz.

b. In the Continent, connect the oven to the power supply 230 V, 50 Hz.

13. Adjust the position of the oven so that the feet of the oven are fitted into the recesses of the spacing

brackets as shown in Fig. 2.
Caution:

Make sure that the power supply cord does not touch the air vent openings behind the oven.

14. Place the built-in frame element 

7

 on top of the oven making sure that it is level both vertically and

horizontally.  Secure loosely to the kitchen cabinet with two screws 

A

 as shown in Fig. 6.

15. Insert two built-in frame side elements 

8

 between the built-in frame element 

7

 and the kitchen cabinet.

And secure two screws 

A

 tightly as shown in Fig. 6. Check location by measuring distance between right

and left built-in frame side elements 

8

. The distance is stated in Fig. 7.

Note: Fit the hole of the built-in frame side element 

8

 to the screw 

A

 when inserting.

16. Install the second built-in frame element 

7

 over the built-in frame side elements 

8 

at bottom edge of

the oven.  And secure the built-in frame element 

7 

through the holes of the built-in frame side elements

8 

to the kitchen cabinet with two screws 

A 

as shown in Fig. 6.

Caution:

Make sure that 6.5 mm of the frames (upper and lower) and cabinet overlap each other as
shown in Fig. 8, or the kitchen cabinet door may touch the built-in frame elements.