R-393 (serv.man7). EBR4800 Built in kit instructions - Sharp Home Appliance User Guide / Operation Manual

r-393 (serv.man7) user guide / operation manual
Model
R-393 (serv.man7)
Pages
16
Size
152.13 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Home Appliance / Microwave Oven / EBR4800 Built in kit instructions
File
r-393-sm7.pdf
Date

Read Sharp R-393 (serv.man7) User Guide / Operation Manual online

ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
NEDERLANDS
ITALIANO
A32867,EBR-4800
1
1
Instruction for SHARP Built-in Kit EBR-4800(SL)
Before installing a Sharp Microwave Oven, read and check the following points.
SAFETY INFORMATION
1.
Except U.K., for use in continental Europe only.
The oven must be connected to an electric circuit provided with a switch (contact gap no less than 3
mm) to disconnect the oven in case of danger.  A safety-device like  a fuse in the installation may be
used as a switch.
2.
Disconnect the oven from the power supply before installation.
3.
Surround
a. Make sure that the EBR-4800 is the correct surround for your oven.
b. The Sharp Microwave Ovens are designed to either stand neatly on a kitchen counter top or to be built
into a fitted kitchen cabinet using the surround.
c. For B type only
, the EBR-4800 surround will become hot during the oven operations with heater(s).
Take care to prevent burns when you use the oven.
4.
Kitchen cabinet
Prepare the kitchen cabinet as follows;
a. The kitchen cabinet must be of the following dimensions as shown in Fig. 1.
WIDTH
: 560 mm - 568 mm
HEIGHT
: 409 mm
DEPTH
: 550 mm - 580 mm
b. Make sure that the back panel 
D
 is always fitted to ensure the correct ventilation of the oven and
that the ventilation gap 
C
 must be 200 mm as shown in Figs 1 and 2.
c. The shelf of the kitchen cabinet should be made to withstand the weight of the microwave oven to
be installed and the heaviest item likely to be cooked in the microwave oven. Refer to the instruction
manual for microwave oven weight.
5.
Installation near to a conventional oven
a. When a microwave oven is to be installed next to a conventional oven, sufficient space between
them should be allowed to prevent overheating as the surround can warp with excessively high
temperatures. Obviously, it is important to adhere strictly to the conventional oven manufacturer's
installation instructions.
b. A built-in microwave oven must not be installed above a conventional oven otherwise the microwave
oven's cooling system may be adversely affected by hot air produced by the conventional oven.
6.
Installation near a refrigerator or freezer
a. If the microwave oven is to be installed above a refrigerator or freezer requiring back ventilation, a
ventilation duct behind the microwave oven must be provided. It is essential that the refrigerator/
freezer manufacturer's installation procedures are followed.
b. Do not install the microwave oven above a refrigerator or freezer which are ventilated at the front.
7.
Fixing
To avoid any possibility of the kitchen cabinet moving when the microwave oven is installed, it is
essential that the kitchen cabinet is fixed to the back wall.
8.
Adjustment and repair
It is dangerous for your oven to be adjusted or repaired by anyone except properly qualified service
technicians trained by Sharp.
If the appliance is ever removed from the cabinet it should be re-installed in accordance with these
instructions, which should be kept in a safe place for future reference.
★ 
For the type of your oven, refer to the operation manual
("IMPORTANT SAFETY INSTRUCTIONS" or "INSTALLATION").
1
2
2
A32867,EBR-4800
2
INSTALLATION INSTRUCTIONS
1. (For U.K. use)
A cut-out will have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The mains plug must be accessible after installation or an all-pole switch disconnection must be
provided with a contact separation of at least 3 mm in each pole.
(For Continental use)
The electric outlet must be installed at 150 mm high from the floor of the built-in cabinet and at 50 mm
from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be accessible after
installation or the oven must be connected to an electric circuit provided with an all-pole switch (contact
gap no less than 3 mm) to disconnect the oven in case of danger. A safety-device like a fuse in the
installation may be used as a switch.
2. Remove the built-in kit from the package.
3. Set the spacing brackets 
1
 on the shelf along the right and left walls of the kitchen cabinet, keeping
a distance of 7mm between the front end of the shelf and the spacing brackets, and attach them with
the four screws 
9
, as shown in Fig. 1.
Caution:
The arrow marks on each spacing bracket should be pointing towards you.
4. (Carry out this step 4 only for B type models)
Remove the screw 
F
 holding the air duct 
G
 to the rear of the oven as shown in Fig. 3.  And release the
tab of the air duct 
G
 from the slit of the rear of the oven.  Then remove the air duct 
G
 from the oven.
5. (Carry out this step 5 only for B type models)
Remove the screw 
H
 holding the back plate 
I
 to the rear of the oven as shown in Fig. 3. And release the
tabs of the back plate 
I
 from the slits of the rear of the oven.
6. Remove the one screw 
E
 from the oven as shown in Fig. 3.
7. Insert the tab of the exhaust duct 
2
 into the slit of the rear of the oven.  And install the exhaust duct 
2
to the rear of the oven with one screw 
0
 as shown in Fig. 4.
8. Let the power supply cord pass through the hole of the lower side of the intake duct 
3
 as shown in Fig. 4.
9. Install the intake duct 
3
 to the rear of the oven with two screws 
0
 and 
E
 (removed at step 6) as shown
in Fig. 4.
Caution:
Avoid pinching the power supply cord between the oven and the intake duct 
3
.
10. Remove the backing paper from the three cushions 
4
5
 and 
6
.  Attach the cushion
4
 at the top of the
intake duct 
3
 and attach the cushions 
5
 and 
6
 at the top of the oven as shown in Figs 5-a and 5-b.
11. (For U.K. use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the power supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.
12. Connect the oven to the power supply.
Caution: a. In U.K., connect the oven to the power supply 230-240 V, 50 Hz.
b. In the Continent, connect the oven to the power supply 230 V, 50 Hz.
13. Adjust the position of the oven so that the feet of the oven are fitted into the recesses of the spacing
brackets as shown in Fig. 2.
Caution:
Make sure that the power supply cord does not touch the air vent openings behind the oven.
14. Place the built-in frame element 
7
 on top of the oven making sure that it is level both vertically and
horizontally.  Secure loosely to the kitchen cabinet with two screws 
A
 as shown in Fig. 6.
15. Insert two built-in frame side elements 
8
 between the built-in frame element 
7
 and the kitchen cabinet.
And secure two screws 
A
 tightly as shown in Fig. 6. Check location by measuring distance between right
and left built-in frame side elements 
8
. The distance is stated in Fig. 7.
Note: Fit the hole of the built-in frame side element 
8
 to the screw 
A
 when inserting.
16. Install the second built-in frame element 
7
 over the built-in frame side elements 
at bottom edge of
the oven.  And secure the built-in frame element 
through the holes of the built-in frame side elements
to the kitchen cabinet with two screws 
as shown in Fig. 6.
Caution:
Make sure that 6.5 mm of the frames (upper and lower) and cabinet overlap each other as
shown in Fig. 8, or the kitchen cabinet door may touch the built-in frame elements.
ENGLISH
DEUTSCH
FRAN
Ç
AIS
ESPA
Ñ
OL
NEDERLANDS
ITALIANO
A32867,EBR-4800
3
3
3
Anleitung zum SHARP-Einbausatz EBR-4800(SL)
Lesen und überprüfen Sie die folgenden Punkte vor Installation des SHARP Mikrowellengerätes.
SICHERHEITSHINWEISE
1.
Mit Ausnahme von Großbritannien, nur für die Verwendung in Kontinental-Europa vorgesehen.
Das Gerät muß an einen Stromkreis mit einem Schalter angeschlossen werden (Kontaktabstand
mind. 3 mm), um das Gerät im Gefahrenfall abschalten zu können. Eine Sicherung in der Installation
kann als Schalter verwendet werden.
2.
Vor Installation des Gerätes den Netzstecker ziehen.
3.
Einbausatz
a. Versichern Sie sich, daß EBR-4800 der richtige Einbausatz für Ihr Gerät ist.
b. Die Mikrowellengeräte von Sharp können als Standgerät auf einer Küchenplatte aufgestellt oder
unter Verwendung des Einbausatzes in einen Küchenschrank eingebaut werden.
c. Nur für Typ B
, die Umgebung des EBR-4800 wird heiß, wenn das Gerät mit Heizelementen betrieben
wird. Vorsicht vor Verbrennungen beim Betrieb des Gerätes.
4.
Einbauschrank
Den Einbauschrank folgendermaßen vorbereiten;
a. Der Einbauschrank muß folgende Abmessungen aufweisen, siehe Fig. 1.
BREITE
: 560 mm - 568 mm
HÖHE
: 409 mm
TIEFE
: 550 mm - 580 mm
b. Um ausreichende Belüftung des Gerätes zu gewährleisten, ist sicherzustellen, daß die rückwärtige
Wand 
D
 stets angebracht ist und daß der Belüftungsabstand 
C
 wie in Fig. 1 und 2 gezeigt 200 mm
beträgt.
c. Der Boden des Einbauschrankes muß so konstruiert sein, daß er das Gewicht des zu installierenden
Gerätes und der darin zubereiteten Lebensmittel tragen kann. Beachten Sie das Gewicht des
Mikrowellengerätes in der Bedienungsanleitung.
5.
Installation in der Nähe eines konventionellen Herdes
a. Wenn ein Mikrowellengerät neben einem konventionellen Herd installiert wird, muß zum Schutz vor
Überhitzen ein ausreichender Abstand zwischen den beiden Geräten eingehalten werden, da der
Einbausatz sich bei übermäßig hohen Temperaturen verziehen kann. Die Installationsanweisungen
für den konventionellen Herd müssen unbedingt beachtet werden.
b. Ein Einbau-Mikrowellengerät darf nicht über einem konventionellen Herd installiert werden, da das
Kühlungssystem des Mikrowellengerätes durch Heißluft, die vom konventionellen Herd erzeugt
wird, beschädigt werden kann.
6.
Installation in der Nähe eines Kühlschrankes oder eines Gefriergerätes
a. Wenn das Mikrowellengerät über einem Kühlschrank oder einem Gefriergerät installiert wird, für die
eine rückwärtige Belüftung notwendig ist, muß für die Belüftung ein Belüftungskanal hinter dem
Mikrowellengerät angebracht werden. Die Installationsanweisungen für den Kühlschrank oder für
das Gefriergerät müssen unbedingt beachtet werden.
b. Das Mikrowellengerät darf nicht über einem Kühlschrank oder einem Gefriergerät installiert werden,
die an der Frontseite belüftet werden.
7.
Befestigung
Um Bewegungen des Einbauschrankes nach der Installation des Mikrowellengerätes zu vermeiden,
muß er stabil an der rückwärtigen Wand befestigt werden.
8.
Einstellung und Reparatur
Es ist gefährlich, das Gerät von einer anderen Person als einem autorisierten und von Sharp ausgebildeten
Wartungstechniker einstellen oder reparieren zu lassen.
Wenn das Gerät aus einem Einbauschrank entfernt wird, muß es bei Wiedereinbau entsprechend dieser
Anleitung installiert werden. Deshalb für zukünftigen Gebrauch die Anleitung an einem sicheren Ort
aufbewahren.
 Für die Type ihres Gerätes, schlagen Sie in der Bedienungsanleitung nach
(
"
WICHTIGE SICHERHEITSHINWEISE" oder 
"
AUFSTELLANWEISUNGEN").
4
4
A32867,EBR-4800
4
INSTALLATIONSANLEITUNG
1. (Für Großbritannien)
Für den Netzstecker muß auf der Seite des Einbauschrankes eine Öffnung gebohrt werden.
Hinweis:
Der  Hauptnetzstecker muß nach der Installation zugänglich sein oder es muß ein
Abtrennschalter vorhanden sein, bei dem die Kontakte an jedem Pol mindestens 3 mm
voneinander entfernt sind.
(Für Kontinental-Europa)
Die Netzsteckdose muß 150 mm über dem Boden des Einbauschrankes installiert werden und 50 mm von
der rechten Wand, wie in Fig. 1 gezeigt. Der Hauptnetzstecker muß nach der Installation zugänglich sein
oder das Gerät muß an einen elektrischen Schaltkreis mit einem Abtrennschalter (Kontaktabstand mind.
3 mm) angeschlossen sein, um das Gerät im Gefahrenfall abschalten zu können. Eine Sicherung als
Schutzvorrichtung kann bei der Installation als ein Schalter verwendet werden.
2. Den Einbausatz aus der Verpackung nehmen.
3. Die Abstandshalter 
1
 entlang der rechten und linken Wand des Einbauschrankes auf dem Boden
positionieren, wobei ein Abstand von 7 mm zwischen der Bodenvorderkante und den Abstandhaltern
einzuhalten ist. Die Abstandhalter wie in Fig. 1 gezeigt mit den vier Schrauben 
9
 befestigen.
Vorsicht:
Die Pfeile auf den Abstandhaltern müssen nach vorne weisen.
4. (Schritt 4 gilt nur für Modelle Typ B)
Die Halteschraube 
F
 des Luftkanals 
G
 an der Geräterückseite entfernen, wie in Fig. 3 gezeigt. Danach
die Lasche des Luftkanals 
G
 aus dem Einschnitt in der Geräterückseite herausnehmen und den Luftkanal
G
 vom Gerät abnehmen.
5. (Schritt 5 gilt nur für Modelle Typ B)
Die Halteschraube 
H
, mit der die Rückplatte 
I
 am Gerät befestigt ist, wie in Fig. 3 gezeigt entfernen.
Danach die Laschen der Rückplatte 
I
 aus den Schlitzen in der Geräterückseite aus den Einschnitten in
der Geräterückseite herausnehmen.
6. Die Schraube 
E
 wie in Fig. 3 gezeigt vom Gerät abnehmen.
7. Die Lasche des Entlüftungskanal 
2
 in den Einschnitt der Geräterückseite einsetzen. Danach den Kanal
2
 mit der im obigen Schritt entfernten Schraube 
0
 befestigen, wie in Fig. 4 gezeigt.
8. Das Netzkabel wie in Fig. 4 gezeigt durch das Loch in der Unterseite des Ansaugkanals 
3
 führen.
9. Den Ansaugkanal 
3
 wie in Fig. 4 gezeigt mit den beiden Schrauben 
0
 und 
E
 (unter Schritt 6
abgenommen) an der Rückseite des Gerätes befestigen.
Vorsicht:
Darauf achten, daß das Netzkabel nicht zwischen dem Gerät und dem Ansaugkanal 
3
eingeklemmt wird.
10. Die Schutzstreifen von den drei Schaumstoffteilen 
4
5
 und 
6
 abziehen und wie in Fig. 5-a und 5-b
gezeigt, Schaumstoffteil 
4
 an der Oberseite des Ansaugkanals 
3
 und die Schaumstoffteile 
5
 und 
6
oben am Gerät anbringen.
11. (Für Großbritannien)
Das Gerät auf die Abstandhalter auf dem Boden des Einbauschrankes stellen und das Netzkabel durch
die Öffnung führen.
(Für Kontinental-Europa)
Das Gerät auf die Abstandhalter auf dem Boden des Einbauschrankes stellen.
12. Das Gerät an die Stromversorgung anschließen.
Vorsicht: a. In Großbritannien muß das Gerät an 230-240V, 50Hz Wechselstrom angeschlossen werden.
b. In Kontinental-Europa muß das Gerät an eine Steckdose mit 230V, 50Hz, Wechselstrom
angeschlossen werden.
13. Das Gerät so aufstellen, daß die Füße des Geräts in die Aussparungen der Abstandhalter passen, wie in Fig. 2.
Vorsicht:
Sicherstellen, daß das Netzkabel nicht mit den Lüftungsöffnungen auf der Rückseite der
Gerätes in Berührung kommt.
14. Das Rahmenbauteil 
7
 auf das Gerät aufsetzen und darauf achten, daß das Teil sich vertikal und horizontal
in der Waage befindet. Am Einbauschrank lose mit den zwei Schrauben 
A
 wie in Fig. 6 gezeigt anbringen.
15. Zwei seitliche Rahmenbauteile 
8
 zwischen die Rahmenbauteile 
7
 und den Einbauschrank schieben. Die zwei
Schrauben 
A
 wie in Fig. 6 gezeigt fest anschrauben. Die Aufstellung durch Messung des Abstands zwischen
dem rechten und linken eingebauten seitlichen Rahmenbauteil 
8
 prüfen. Der Abstand ist in Fig. 7 angezeigt.
Hinweis:
Beim Einschieben die Öffnung des eingebauten seitlichen Rahmenbauteils 
8
 mit der
Schraube 
A
 angleichen.
16. Das zweite Rahmenbauteil 
7
 über dem eingebauten seitlichen Rahmenbauteil 
8
 auf der Unterkante des
Gerätes anbringen. Den Rahmenbauteil 
7
 durch die Öffnungen des seitlichen Rahmenbauteils 
8
 am
Einbauschrank mit den zwei Schrauben 
A
 wie in Fig. 6 gezeigt befestigen.
Vorsicht:
Sicherstellen, daß der Rahmen (oben und unten) den Schrank wie in Fig. 8 gezeigt um nur
6,5 mm überlappt. Anderenfalls kann es vorkommen, daß die Einbauschranktür die
Rahmenbauteile berührt.
Page of 16
Display

Download Sharp R-393 (serv.man7) User Guide / Operation Manual

Here you can read online and download Sharp R-393 (serv.man7) User Guide / Operation Manual in PDF. R-393 (serv.man7) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp R-393 (serv.man7) Microwave Oven. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.