R-238ASL (serv.man9). Touch Control Panel Assembly - Sharp Home Appliance Service Manual (repair manual). Page 3

R238A(SL)

9 – 3

This unit uses CMOS LSI in the integral part of the circuits. When han-
dling these parts, the following precautions should be strictly followed.
CMOS LSI have extremely high impedance at its input and output ter-
minals. For this reason, it is easily influenced by the surrounding high
voltage power source, static electricity charge in clothes, etc., and
sometimes it is not fully protected by the built-in protection circuit.

In order to protect CMOS LSI.

1) When storing and transporting, thoroughly wrap them in aluminium

foil. Also wrap PW boards containing them in aluminium foil.

2) When soldering, ground the technician as shown in the figure and

use grounded soldering iron and work table.

We describe the procedures to permit servicing of the touch control
panel of the microwave oven and the precautions you must take when
doing so. To perform the servicing, power to the touch control panel is
available either from the power line of the oven itself or from an exter-
nal power source.

1. Servicing the touch control panel with power supply of the oven:

CAUTION: THE HIGH VOLTAGE TRANSFORMER OF THE MICRO-

WAVE OVEN IS STILL LIVE DURING SERVICING AND
PRESENTS A HAZARD.

Therefore, before checking the performance of the touch control
panel,

1) Disconnect the power supply cord and then remove outer case.

2) Open the door and block it open.

3) Discharge high voltage capacitor.

4) Disconnect the leads to the primary of the power transformer.

5) Ensure that these leads remain isolated from other components

and oven chassis by using insulation tape.

6) After that procedure, re-connect the power supply cord.

After checking the performance of the touch control panel,

1) Disconnect the power supply cord.

2) Open the door and block it open.

3) Re-connect the leads to the primary of the power transformer.

4) Re-install the outer case (cabinet).

5) Re-connect the power supply cord after the outer case is

installed.

6) Run the oven and check all functions.

a) On some models, the power supply cord between the touch

control panel and the oven itself is so short that the two can't
be separated. For those models, check and repair all the
controls (sensor-related ones included) of the touch control
panel while keeping it connected to the oven.

b) On some models, the power supply cord between the touch

control panel and the oven proper is so long enough that
they may be separated from each other. For those models,
therefore, it is possible to check and repair the controls of the
touch control panel while keeping it apart from the oven
proper; in this case you must short both ends of the door
sensing switch (on PWB) of the touch control panel with a
jumper, which brings about an operational state that is equiv-
alent to the oven door being closed. As for the sensor-
related controls of the touch control panel, checking them is
possible if the dummy resistor(s) with resistance equal to
that of the controls are used.

2. Servicing the touch control panel with power supply from an exter-

nal power source:

Disconnect the touch control panel completely from the oven
proper, and short both ends of the door sensing switch (on PWB) of
the touch control panel, which brings about an operational state
that is equivalent to the oven door being closed. Connect an exter-
nal power source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls of the
touch control panel; it is also possible to check the sensor-related
controls of the touch control panel by using the dummy resistor(s).

Tools required to service the touch control panel assembly.

1) Soldering iron: 60W

(It is recommended to use a soldering iron with a grounding termi-
nal.)

2) Oscilloscope: Single beam, frequency range: DC - 10MHz type or

more advanced model.

3) Others: Hand tools

1) Before turning on the power source of the control unit, remove the

aluminium foil applied for preventing static electricity.

2) Connect the connector of the key unit to the control unit being sure

that the lead wires are not twisted.

3) After aluminium foil is removed, be careful that abnormal voltage

due to static electricity etc. is not applied to the input or output ter-
minals.

4) Attach connectors, electrolytic capacitors, etc. to PWB, making

sure that all connections are tight.

5) Be sure to use specified components where high precision is

required.

63

BZO90

OUT

Signal to sound buzzer (2.0 kHz).
A: key touch sound.
B: Completion sound.

64

P20

OUT Terminal not used.

A

B

0.1 sec.

2.0 sec.

H : GND

L : -5V

H : GND

L : -5V

approx. 1M ohm