Read Sharp UP-5300 (serv.man2) Service Manual online
CHAPTER 4. COMMAND DESCRIPTION
1. Command table
No.
Command
Function
Remarks
1
[LF]
Causes print and line feed.
2
[FF]
Causes page-mode print and return to standard
mode.
mode.
Valid for page-mode.
3
[CAN]
Cancels print data.
4
[SI]
Selects character height reduction.
Valid only at the beginning of a line.
5
[DC2]
Cancel character height reduction
Valid only at the beginning of a line.
6
[DLE] [EOT] [n]
Transmits status in real time.
Transmits regardless of the state of the host
computer.
computer.
7
[DLE] [ENQ] [n]
Requests the printer in real time.
Transmits regardless of the state of the host
computer.
computer.
8
[ESC] [FF]
Causes page-mode data print.
Valid for page-mode.
9
[ESC] [SP] [n]
Sets character right-side spacing.
10
[ESC] ! [n]
Sets character mode.
Font, height and width are set.
11
[ESC] $ [n1] [n2]
Sets absolute print starting position.
12
[ESC] % [n]
Selects/cancels user-defined character.
The preset user-defined character is called.
13
[ESC] & [03] [C1] [C2] [[n]
[DATA] (3xn)] (C2 – C1+1)
[DATA] (3xn)] (C2 – C1+1)
Defines user-defined character.
14
[ESC] * [m] [n1] [n2] [DATA] k
Sets bit image data.
This image shows the same movement as a
normal character (it can be printed using LF).
The setting is possible during printing.
normal character (it can be printed using LF).
The setting is possible during printing.
15
[ESC] -[n]
Selects/cancels underline.
16
[ESC] 2
Selects 30/203 inch (30 dot) line feed.
Valid even during printing.
17
[ESC] 3 [n]
Sets line feed amount.
Valid even during printing.
18
[ESC] 4 [n] [DATA] (72xn)
Sets logo stamp.
Sets data to stamp No. 0
19
[ESC] 6 [m] [n] [DATA] (72xn)
Sets logo stamp.
Sets data to stamp No. [m]
20
[ESC] = [n]
Sets peripheral device.
21
[ESC] ? [n]
Deletes user-defined character.
The same pattern as the internal character is
printed after deletion.
printed after deletion.
22
[ESC] @
Initializes printer.
23
[ESC] J [n]
Prints and feeds paper.
24
[ESC] L
Switches from standard to page-mode.
Valid only at the beginning of a line.
25
[ESC] R [n]
Selects international character.
26
[ESC] S
Switches from page to standard mode.
Valid only at the beginning of a line.
27
[ESC] V [n]
Sets/cancels 90° clockwise rotated character.
28
[ESC] ¥ [n1] [n2]
Sets relative position.
Sets the print starting position based on the
current position.
current position.
29
[ESC] a [n]
Aligns print data positions
Valid only at the beginning of a line.
30
[ESC] c4 [n]
Selects paper-out detector to stop printing.
31
[ESC] c5 [n]
Enables/disables panel switch.
32
[ESC] d [n]
Prints and feeds paper by the specified number of
lines.
lines.
33
[ESC] i
Cuts paper.
Valid only at the beginning of a line.
34
[ESC] m
Cuts paper.
Valid only at the beginning of a line.
35
[ESC] o
Prints stamp.
Valid only at the beginning of a line.
Prints stamp No. 0
Prints stamp No. 0
36
[GS] o [m]
Prints stamp.
Valid only at the beginning of a line.
Prints stamp No. [m]
Prints stamp No. [m]
37
[ESC] q [n]
Sets power failure mark.
38
[ESC] t [n]
Selects character code table.
39
[ESC] v
Transmits paper detector status.
40
[ESC] [n]
Sets/cancels upside-down character printing.
Valid only at the beginning of a line.
41
[GS] ! [n]
Selects character size.
42
[GS] * [n1] [n2] [data]
(n1xn2x8)
(n1xn2x8)
Sets image data.
43
[GS] / [n]
Prints image data.
44
[GS] :
Sets starting/ending position of macro definition.
45
[GS]^ [r] [t] [m]
Executes macro.
The number of times, interval and mode of
execution can be set.
execution can be set.
46
[GS] E [n]
Selects print density.
4 – 1
Click on the first or last page to see other UP-5300 (serv.man2) service manuals if exist.