Read Sharp UP-5300 (serv.man2) Service Manual online
CHAPTER 3. INITIAL PROCESSING
The following seven modes are available when turning ON the power
(performing initial processing).
(performing initial processing).
Mode
Key sequence
Operation
MASTER
RESET mode
RESET mode
Turn ON the power while
pressing the ONLINE key
and PAPER FEED key.
pressing the ONLINE key
and PAPER FEED key.
The printer clears the preset
data/receive buffer and
starts operating.
Print out MRS printer status.
data/receive buffer and
starts operating.
Print out MRS printer status.
Set MRS switch ON and
turn ON the power.
turn ON the power.
The printer clears the preset
data/receive buffer and
starts operating.
Not print out MRS printer
status.
data/receive buffer and
starts operating.
Not print out MRS printer
status.
IPL mode
Set DIP SW 2-1 to IPL
mode and turn ON the
power while pressing the
ONLINE key and PAPER
FEED key.
IPL mode is entered when
the PAPER FEED key is set
to ON.
mode and turn ON the
power while pressing the
ONLINE key and PAPER
FEED key.
IPL mode is entered when
the PAPER FEED key is set
to ON.
The printer clears the
application program area of
the flash ROM and receives
the application program
data from the PC via RS232.
application program area of
the flash ROM and receives
the application program
data from the PC via RS232.
RESUMPTION
mode
mode
Set MRS switch OFF and
turn ON the power.
turn ON the power.
The printer resumes the
printing interrupted by
power failure.
printing interrupted by
power failure.
DIAG mode
Turn ON the power while
pressing the PAPER FEED
key.
pressing the PAPER FEED
key.
The printer performs the
DIAG operation.
DIAG operation.
HEXADECIMAL
DUMP mode
DUMP mode
Turn ON the power while
pressing the ONLINE key.
Release ONLINE key.
Press ONLINE key.
pressing the ONLINE key.
Release ONLINE key.
Press ONLINE key.
The printer prints the data
sent from the host
computer, using
hexadecimal digits and
characters corresponding to
them.
sent from the host
computer, using
hexadecimal digits and
characters corresponding to
them.
DEMO mode
Turn ON the power while
pressing the ONLINE key.
Release ONLINE key.
Press PAPER FEED key.
pressing the ONLINE key.
Release ONLINE key.
Press PAPER FEED key.
The printer prints the
demonstration data.
demonstration data.
Ignore CTS
mode
mode
Turn ON the power while
pressing the ONLINE key.
Press PAPER FEED key
before release ONLINE key.
pressing the ONLINE key.
Press PAPER FEED key
before release ONLINE key.
The printer clears the preset
data/receive buffer and
starts operating.
The printer receives data
regardless CTS status.
data/receive buffer and
starts operating.
The printer receives data
regardless CTS status.
Print/Display Operation
1. MASTER RESET mode
Print: The DIP switch settings are printed.
123456789012345678901234567890123456789012345678
***MASTER RESET
BPS 38400BPS
2400BPS ~ 38400BPS
BIT FORMAT 8BIT
7BIT
PARITY NONE
EVEN/ODD
HANDSHAKING DTR/DSR
XON/XOFF
BUSY CONDITION BUFFER FULL
OFF LINE
PRINT DENSITY LEVEL5
LEVEL1 ~ LEVEL8
PRINT SPEED 75mm/s
60mm/s / 50mm/s
VERSION No. 1A
Print cut
Display:
The ONLINE lamp is turned ON when the printer sets
ready to receive data from the host computer.
ready to receive data from the host computer.
2. IPL mode
Print: Nothing is printed.
However, if the power is turned ON in the IPL mode without
pressing any key, the following is printed.
pressing any key, the following is printed.
For details, see the IPL detailed specification.
3. RESUMPTION mode
Print:
The printer resumes the printing interrupted by a power
failure.
When a power failure occurs during printing, performs
power failure mark “= = = = =” and executes the printing
again.
The power failure mark can be set in the [ESC] sequence.
failure.
When a power failure occurs during printing, performs
power failure mark “= = = = =” and executes the printing
again.
The power failure mark can be set in the [ESC] sequence.
Display:
The ONLINE lamp is turned ON when the printer gets
ready to receive data from the host computer.
ready to receive data from the host computer.
4. DIAG mode
For details, see the DIAG specification.
5. HEXADECIMAL DUMP mode
Print:
For details, see the HEXADECIMAL DUMP specification.
6. DEMO mode
Print:
Printer prints "DEMO" and several pattern of character lines.
7. Ignore CTS mode
Print:
Others:
If only the IPL program is in the flash ROM (the application
program does not exist there), the following display is
produced.
program does not exist there), the following display is
produced.
That causes the ONLINE lamp and ERROR lamp to blink
at the same time.
at the same time.
3 – 1
Click on the first or last page to see other UP-5300 (serv.man2) service manuals if exist.